Fisher & Paykel OR90SDBGFX installation instructions Connecting the cooker to the gas supply

Page 12

10

Installation instructions

Connecting the cooker to the gas supply

The gas connection must be carried out by an authorised person according to the relevant standards.

Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the washer has been placed (see Fig.s 11-12 following).

Conical adaptor and washer are supplied with the appliance (packed with conversion kit for use with Natural gas or LPG).

This appliance is suitable for use with Natural gas or LPG. (Check the “gas type” sticker attached to the appliance).

For Natural gas, connect the gas supply to the gas pressure regulator which is supplied with the appliance (Fig.12). Adjust the regulator to obtain a test point pressure of 1 kPa with the two semi-rapid burners operating at the maximum.

For LPG, connect the gas supply to the test point adaptor which is supplied with the appliance (Fig.11). Ensure that the supply pressure is regulated to 2.75 kPa.

The connection must be made at the rear of appliance (left or right); the pipe is not to cross the cooker.

Close off the unused inlet with the cap and sealing washer supplied (Fig. 13). IMPORTANT: Use two spanners to tighten or loosen the connecting pipe (Fig.13).

Installation with a flexible hose assembly

If this appliance has to be installed with a hose assembly, the installer shall refer to the network operator or gas supplier for confirmation of the gas type, if in doubt.

When used with a flexible hose, the connector on the wall should be between 450 mm to 500

mmfrom the floor and 200 mm to 300 mm from the left-hand side of the appliance as viewed from the front. The hose connection on the appliance shall face downwards.

It is important that the hose does not come in contact with the metal of the appliance and is secured as per appropriate gas installation codes. A chain 80% of the length of the flexible gas hose must be used to prevent stress being applied to the hose. The chain should be attached securely to the product where shown (see Fig.13), and on the wall.

Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified. The thread connection shall be Rp ½” (ISO 7-1) male.

Important!

After connection the installer must check that the hose is not kinked, subjected to abrasion or permanently deformed. The installer must check also that the hose is not near or in contact with any hot surfaces.

The hose assembly shall be as short as practicable and comply with relevant AS5601 / NZS5261 requirements.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation instructions Page Contents Safety and warnings InstallationGeneral Power supply 220-240V~ 3680W 50/60Hz ElectricalOperation Important safety instructions Installation instructions Dimensions and clearancesFitting the adjustable feet Locating the area for gas and electrical connectionLevelling the cooker Moving the cooker Fixing the backguardFitting the anti-tilt bracket To fit the anti-tilt bracketConnecting the cooker to the gas supply Installation with a flexible hose assemblyFitting the brass conical adaptor Fitting the cap onInlet pipe terminal not used Leak-testing and flame-testing the cooker Adjusting the minimum burner settingConverting to a different gas type Replacing the injectorsInjector InjectorsJ forAdjusting the minimum burner setting Semi-rapid and triple-ring burnersInside crown of dual burner Outside crown of dual burnerLPG Wiring diagram Wiring diagram key Using your seven-function oven for the first time Before using your new oven, pleaseSetting the clock Illuminated symbolsButtons To set the clockUsing your oven Function and temperature dialsCooking functions BakeBaking chart Using the rotisserie Lock studRotate the fork screws to Loosen and tighten Fork Skewer Rotisserie drive holeUsing the electronic timer Automatic cooking To set the oven for automatic cookingUsing your gas cooktop Gas burnersSemi-rapid and triple-ring wok burners 0 = closed valve OFF Dual burnerBefore using your cooktop Using the gas burnersFlame failure safety feature If a burner does not light If the flame is irregularMatching cookware to burner Diameters of pans which may be used on the cooktopSmall pan support Wok standCare and cleaning General adviceCleaning the outside of the cooker Cleaning the gas cooktopBurner parts and trivets Replacing the semi-rapid burnersReplacing the triple-ring wok and dual burners Correct positioningCleaning the inside of your oven Drop-down grill elementCleaning the enamel cavity Cleaning the fat filterCleaning the grill tray and shelves Fitting and removing the sliding shelf supports Fitting the sliding shelf supportsTurn the power to the cooker off at the wall Storage compartmentReplacing the oven lamp Care and cleaning Removing the oven door Removing the inner pane of glass Remove the inner glass retainerRemove the inner glass pane Removing the inner glass paneAfter cleaning, replace the inner glass pane When replacing the inner glass pane, make sure thatReplace the glass retainer Replace the glass retainerRefit the door Troubleshooting Problem Possible solutionsWarranty and service Before you call for service or assistanceProduct details Page Page Page Page NZ AU

OR90SDBGFX specifications

Fisher & Paykel has long been synonymous with innovative and high-quality kitchen appliances, and the OR90SDBGFX oven is a stellar example of their commitment to excellence. This freestanding range offers a blend of advanced technology, stylish design, and practical functionality, making it an ideal choice for any modern kitchen.

One of the standout features of the OR90SDBGFX is its large 90-litre capacity oven. This spacious design allows for multiple dishes to be cooked simultaneously, making family meals and gatherings a breeze. The oven is equipped with six cooking functions, including bake, grill, and fan-forced modes, giving users the versatility to prepare a wide variety of dishes to perfection. The self-cleaning function is an added convenience that helps maintain the oven's pristine condition with minimal effort.

The OR90SDBGFX also incorporates Fisher & Paykel's innovative AeroTech technology, which ensures consistent cooking temperatures throughout the oven. This feature minimizes temperature fluctuations, allowing for even baking and roasting results. The dual fan system further improves heat distribution, making it easier to achieve desired outcomes whether you're baking delicate pastries or roasting large cuts of meat.

Stylish and durable, the exterior of the OR90SDBGFX features a sleek stainless steel finish that not only enhances its aesthetic appeal but also ensures longevity. The integrated wok burner offers high-powered cooking options, perfect for Asian-inspired dishes and stir-fry. With five burners in total, home chefs can enjoy the flexibility of using multiple pots and pans at once.

Another notable characteristic of this range is the intuitive control panel featuring modern dials and an easy-to-read display. Precise temperature control and multifunction settings make cooking more enjoyable and accessible for both novice cooks and seasoned chefs. Additionally, the range comes standard with safety features such as flame failure protection and a cooling fan, ensuring peace of mind during cooking.

Fisher & Paykel thoughtfully designed the OR90SDBGFX to cater to the needs of today's culinary enthusiasts. Its combination of significant capacity, advanced cooking technologies, stylish design, and user-friendly features makes it an outstanding choice for any kitchen renovation or upgrade. Whether you're preparing everyday meals or hosting dinner parties, the OR90SDBGFX delivers unparalleled performance and reliability, embodying the brand's commitment to quality and innovation.
Top Page Image Contents