GE ZIS420NX dimensions Product Clearances, Water and electrical locations, Cutout depth must be

Page 1
*84" From Floor to Top Frame

ZIS420NX

GE Monogram® 42" Built-In Side-by-Side Refrigerator

Dimensions and Installation Information (in inches)

The Installation Space

41"

Case Width 25-3/8

*83-1/2" at Rear

26-7/8"

42"

Frame to Frame

including

 

handle

 

*Shipping height. The refrigerator can be adjusted to fit into a cutout that is 83-1/2" min. to

84-1/2” max. height. Note that the top case trim at the front is 1/2" higher and will overlap upper cabinetry or soffit. Use leveling legs and wheels for a maximum 1" height adjustment.

35-1/2" for 36" models

 

 

 

 

 

 

 

 

 

 

 

 

36" Models 12"

41-1/2" for 42" models

 

 

 

 

 

 

 

 

42" Models 18"

 

 

 

 

 

 

 

 

 

 

 

47-1/2" for 48" models

 

 

 

 

 

 

 

 

48" Models 20"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*Finished

 

Width

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

84-1/2" max

Electrical

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5"

 

 

 

 

83-1/2" min

Area

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Finished

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75" From Floor

Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to Bottom

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24"

 

 

 

 

 

 

 

 

 

 

 

 

of Electrical

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Area

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5"

 

Water Supply

5"

3-1/2"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Product Clearances

These refrigerators are equipped with a 2 position door stop. The factory set 130° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.

3-1/2"

Water and electrical locations

The opening must be prepared with the electrical and water supply located as shown.

130° Door Swing

13"

19"

90° Door Swing

23-7/8" Behind Frame

28-5/8"

4" Min. to Wall

The cutout depth must be 24".

The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation.

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or circuit

Allow minimum clearances for freezer door and fresh food door for a full 130° door swing and to allow for pan removal.

4" minimum clearance is required when door swing is adjusted to 90°. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.

Installation Information: Before installing, consult installation instructions packed with product, or online at Monogram.com, for current dimensional data.

For answers to your Monogram,® GE Profileor GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.

breaker is recommended. Install a properly grounded 3-

prong electrical receptacle recessed into the back wall.

Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

Water line can enter the opening through the floor or back wall. The water line should be 1/4" O.D. copper tubing or GE SmartConnectkit between the cold water line and water connection location, long enough to extend to the front of the refrigerator. Installation of an easily accessible shut off valve in the water line is recommended.

Listed by

Underwriters

Laboratories

Specification Revised 11/08

110166

Image 1
Contents Specification Revised 11/08 Additional SpecificationsProduct Clearances Water and electrical locationsAccessory Panels Optional Accessory KitFramed Panels Door Handles Side PanelsDimensions and Installation Information in inches Framed Panel DimensionsSide-by-Side in inches Important Note Maximum totalTop View Door Swing Factory setting ScaleAdvance Planning for Built-In Side-by-Side Refrigerators Door Swing Optional setting ScaleFeatures and Benefits