GE r10965v-1 owner manual Automatic icemaker, Special notes

Page 17

Automatic Icemaker

Automatic icemaker

Stainless Steel Refrigerator

NOTE: A newly installed refrigerator may take 12 to 24 hours to begin making ice.

The icemaker will produce seven cubes per cycle—approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply, set the power switch to the ON position.

The icemaker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

Special notes:

•Dispenser models have a tilt-out ice bin. The bin can be tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

•To restore your ice level from an empty bucket stage, the following steps are recommended:

112 hours after the first batch of ice has fallen into the bin, dispense 3 to 4 cubes.

2After an additional 6 hours, dispense 3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of time.

Icemaker

Power Switch

Feeler Arm

To access ice or reach the power switch:

1Lift the bin, then pull it forward until the bin stops.

2Lower the bin to access ice or reach the power switch.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Monogram.com Side-by-Side Stainless Steel Free-Standing RefrigeratorsIntroduction ContentsBefore using your refrigerator Write down the model & serial numbers Consumer Information If you need serviceIf you received a damaged refrigerator Save time & money For customers in CanadaBefore You Throw Away Your Old Refrigerator or Freezer Read and Save These InstructionsLire ET Conserver CES Instructions HOW to Connect Electricity Raccordement Électrique To turn the cooling system off, tap Temperature controlsPerformance Air Flow System How it works How to useCustomCool CustomCool chart Water filter cartridge Replacement Filters To order additional filter cartridgesUnited States, call GE Parts and Accessories Large Bins Slide-out spillproof shelfFreezer baskets QuickSpace shelfSlide-out freezer shelves Fixed freezer shelvesDoor alignment Refrigerator doorsCrispers and Pans Fruit and vegetable crispersSpecial notes Automatic icemakerRemoving ice bin Mise EN Garde La glaceDispenser Light Door Alarm Using the dispenserOther dispenser controls Important facts about the dispenserCleaning the inside Cleaning the outsideDispenser drip Do not use appliance wax or polish on the stainless steelPreparing for vacation Care and CleaningPreparing to move Be sure the refrigerator stays in an uprightFresh food Replacing the Light BulbsCompartment Upper lightNormal operating sounds Problem SolverProblem Possible Cause Questions? Use this problem solver Problem SolverFrequent Questions? Use this problem solver Food ISN’T Special Notices Operating SpecificationsGeneral Installation/Operation/Maintenance Requirements Water Treatment Device Certificate Number Stainless Steel Refrigerator In-Home Repair From Date Original Purchase Your Monogram Refrigerator Warranty

r10965v-1 specifications

The GE R10965V-1 is a notable electrical component that exemplifies advanced engineering in the field of electrical applications. This product is primarily recognized for its versatility and reliability, making it ideal for various industrial and commercial applications.

One of the standout features of the GE R10965V-1 is its robust design, which allows it to operate effectively under extreme conditions. Its durable construction ensures longevity, reducing the need for frequent replacements. The unit is built to withstand high temperatures, moisture, and other potentially damaging environmental factors, making it suitable for outdoor and challenging industrial environments.

The GE R10965V-1 incorporates advanced semiconductor technology, which enhances its efficiency and performance. This technology allows for better thermal management, reducing overheating risks and increasing the overall lifespan of the component. Additionally, the device supports a wide range of operating voltages, making it highly adaptable to various electrical systems.

Another significant characteristic of the GE R10965V-1 is its high current capacity. This feature is particularly beneficial for applications requiring substantial power supply, as it ensures that the device can handle increased loads without compromising performance. The internal circuitry is designed to minimize losses, further enhancing its reliability and operational efficiency.

In terms of safety, the GE R10965V-1 employs multiple protective features to prevent short circuits, overloads, and other electrical hazards. These safeguards contribute to overall system stability, making it a preferred choice for engineers and technicians who prioritize safety in their designs.

The installation process for the GE R10965V-1 is user-friendly, with straightforward wiring and mounting options that simplify integration into existing systems. This ease of installation is a considerable advantage for maintenance teams, as it reduces downtime and operational disruptions.

Compatibility is another defining aspect of the GE R10965V-1. It is designed to work seamlessly with a variety of control systems and monitoring tools, facilitating enhanced functionality and performance measurement. Users often appreciate this versatility, as it allows for easier upgrades and system enhancements.

Overall, the GE R10965V-1 stands out in the market due to its combination of durable construction, advanced technology, high current capacity, and safety features. It caters to a broad spectrum of applications and is widely regarded for its reliability and efficiency in delivering electrical power. As industries continue to evolve and demand more robust electrical solutions, the GE R10965V-1 remains a vital component for enabling progress.
Top Page Image Contents