GE 1825 owner manual What You Will Need, Power drill

Page 26

Customer Service Troubleshooting Tips Installation Instructions Operating Instructions Safety Information

Installing the water line.

Read these instructions completely and carefully.

What You Will Need

To determine how much copper tubing you need:

Measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then add 8 feet (244 cm). Be sure there is sufficient extra tubing [about 8 feet (244 cm) coiled into 3 turns of about 10 inches (25 cm) diameter] to allow the refrigerator to move out from the wall after installation.

■A water supply kit (containing copper tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories, 800-626-2002.

■A cold water supply. The water pressure must be between 20 and 120 p.s.i.

■Power drill.

■Copper tubing, 1/4″ outer diameter to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square.

Do not use plastic tubing or plastic fittings because the water supply line is under pressure at all times. Certain types of plastic tubing may become brittle with age and crack, resulting in water leakage.

■Two 1/4″ outer diameter compression nuts and 2 ferrules (sleeves)— to connect the copper tubing to the shutoff valve and the refrigerator water valve.

■If your existing water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting.

■Shutoff valve to connect to the cold water line. The shutoff valve

should have a water inlet with a minimum inside diameter of 5/32″ at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents GE Appliances Write the model and serial numbers here Staple sales slip or cancelled check hereCongratulations You Are Now Part of the GE Family Review the Section on GE & You Service PartnershipRead this Manual Safety Precautions InstructionsBefore You Throw Away Your Old Refrigerator or Freezer CFC DisposalUSE of Adapter Plugs REMEMBER… About the controls on the refrigerator Control Settings Power Saver SwitchHow To Test Temperatures Food StorageRearranging the Shelves Safety InformationAbout the refrigerator shelves and dishes Quick Serve SystemAbout the refrigerator bins Quick Store BinAbout the storage drawers Adjustable Humidity DrawersAdjustable Temperature Meat Drawer Fruit and Vegetable DrawersSnuggers About the additional featuresStorage Drawers To RemoveBeverage Rack Two-Position Freezer ShelfCondiment Caddy Extra Freezer Shelf Bins on the Doors Can DispenserAutomatic Icemaker on some models Icemaker Accessory KitAbout the automatic icemaker Ice Storage Bin About the ice and water dispenserTo Use the Dispenser To replaceWater Filter Accessory Important Facts About Your DispenserCare and cleaning of the refrigerator Press here to Cleaning the OutsideUnder the Refrigerator Cleaning the InsideTroubleshooting Tips Customer Service Preparing for Vacation Light Bulb ReplacementBehind the Refrigerator Preparing to MoveClearances Preparing to install the refrigeratorRefrigerator Location To adjust the rollers Rollers have 3 purposesInstalling the water line Before You BeginPower drill What You Will NeedInstall the Shutoff Valve Shut Off the Main Water SupplyRoute the Copper Tubing and Connect It to the Shutoff Valve Turn On the Water and Flush Out the TubingPlug In the Refrigerator Connect the Tubing to the RefrigeratorTurn the Water On at the Shutoff Valve Start the IcemakerTools Required When reversing the door swing on non-dispenser modelsImportant Notes Before Removing the Doors Remove the Freezer Door on Non-Dispenser ModelsRemoving the doors Remove the Fresh Food Door Reversing the hardwareRemove the Freezer Door on Dispenser Models Transfer Bottom Hinge Bracket to the LeftTransfer Top Hinge to the Left Operating Instructions Safety InformationTransfer Center Hinge Bracket to the Left Transfer Door StopsTransfer Freezer Door Handle Information Operating Instructions InstallationReversing the door handles Plastic Washer Reversing the doors Rehang the Freezer Door on Dispenser ModelsNormal operating sounds Operate Before you call for service…Refrigerator does not Vibration or rattlingAutomatic icemaker Fresh food or freezerPackage is normal Does not workOdor/taste Power Saver settingIce cubes have Moisture forms onFreezer Door does not close Hot air from bottomOrange glow See RollersCustomer Service Customer Service Safety Information Next Four Years Consumer WarrantyFirst Year Terms and ConditionsGE Will Replace What GE Will Not CoverGE Answer Center In the U.S Service Telephone NumbersService Contracts In the U.S Canada, call

1825 specifications

The GE 1825 is a remarkable evolution in the world of gas turbine technology, produced by General Electric, a company renowned for its innovative engineering and commitment to power generation solutions. Launched as part of GE's 7FA series, the 1825 model has established itself as a pivotal asset for both industrial and utility applications.

One of the standout features of the GE 1825 is its design efficiency. Engineered to deliver a high output while ensuring low emissions, this gas turbine operates effectively in combined cycle settings, making it an ideal choice for power plants aiming to optimize their production capabilities. With a robust output capability of around 1825 megawatts, the turbine is well-suited for large-scale operations requiring reliable energy generation.

The GE 1825 employs advanced technologies to enhance its performance. The turbine incorporates sophisticated air-cooled components, which help maintain operational integrity at elevated temperatures. This design focuses on durability and longevity, minimizing the need for frequent maintenance. Moreover, the GE 1825 turbine utilizes a state-of-the-art combustion system that not only boosts its thermal efficiency but also reduces nitrogen oxide emissions, aligning with global environmental standards.

Another notable characteristic of the GE 1825 is its operational flexibility. This turbine can seamlessly adapt to various fuel sources, including natural gas, distillate oil, and other alternative fuels. Such versatility enables power plants to optimize their fuel consumption based on market conditions and availability, thus achieving better economic performance.

In terms of control technologies, the GE 1825 is equipped with advanced digital systems that facilitate real-time performance monitoring and predictive maintenance. This capability allows operators to maintain optimal performance levels while ensuring that potential issues are identified and addressed before they escalate into critical problems.

Ultimately, the GE 1825 gas turbine stands as a testament to General Electric's commitment to energy innovation, providing cutting-edge technologies, exceptional efficiency, and operational flexibility. With its high power output, reduced emissions, and advanced control systems, it plays a crucial role in the evolving landscape of power generation, meeting both economic and environmental challenges in today’s energy market.
Top Page Image Contents