Control

Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m2 per 8 g of R 600a refrig- erant used in the appliance. If the room in which the appliance is installed is too small, a flammable gas-air mixture may form in the event of a leakage in the refrigeration circuit. The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance.

WARNING

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause short circuits.

u The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.

WARNING

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flammable. Escaping refrigerant may ignite.

u Do not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

u Do not place appliances emitting heat e.g. microwaves, toasters etc. on the appliance!

WARNING

Fire hazard and risk of damage due to blocked ventilation grille! u Always keep the ventilation grille free. Always ensure that the

appliance is properly ventilated.

u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because other- wise there will be vibratory noise!

After installation:

u Remove all transit supports. u Unscrew the red transport lock.

Close the vacated retaining hole using the stopper (60).

u Dispose of packaging material (see 4.3) .

For Side-by-Side installation, freezer and refrigerator side by side:

u Always install the freezer on the right of the refrigerator, as seen from the front.

w No condensate forms between the appliances thanks to the side wall heating system foamed in on the left.

Ventilation is effected by way of the plinth.

If the appliance is installed in a very damp environment, conden- sate may form on the outside of the appliance.

u Always see to good ventilation at the installation site.

The packaging is made of recyclable materials:

-corrugated board/cardboard

-EPS moulded parts

-polythene bags and sheets

-polypropylene straps

uTake the packaging material to an official collecting point.

4.4 Connecting the appliance

NOTICE

Risk of damage to the electronic control system!

u Do not use stand-alone inverters (conversion of d.c. to a.c./ three-phase) or energy saving plugs.

WARNING

Fire and overheating hazard!

u Do not use extension cables or multiple socket outlets.

The type of current (alternating current) and voltage at the instal- lation site have to conform with the data on the type plate (see Appliance at a glance).

Connect the appliance only with a properly installed socket outlet with earthing contact. The socket outlet must be fused with 10 A or higher.

uCheck the electrical connection.

uClean the appliance (see 6.2) .

uPlug in the power plug.

4.5 Switching on the appliance

u Press On/Off button Fig. 2 (1).	display and
w The appliance is switched on. The temperature

the alarm button flash until the temperature is sufficiently cold.

5 Control

5.1 Temperature alarm

The audible alarm sounds if the freezer temperature is not cold enough.

The alarm button flashes at the same time.

The cause of the temperature being too high may be:

-warm fresh food was placed inside

-too much warm ambient air flowed in when rearranging and removing food

-power failure for some time

-the appliance is faulty

The audible alarm is automatically silenced, the alarm button Fig. 2 (5) goes out and the temperature display stops flashing when the temperature is sufficiently cold again.

If the alarm status persists: (see Malfunction).

Note

Food may be spoilt if the temperature is not cold enough.

u Check the quality of the food. Do not consume spoiled food.

4.3 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film! u Do not allow children to play with packing material.

5.1.1 Muting the temperature alarm

The audible alarm can be muted. When the temperature is suffi- ciently cold again, the alarm function is active again.

u Press alarm button Fig. 2 (5). w The audible alarm is silenced.

UIG1313 specifications

The Liebherr UIG1313 is a cutting-edge machine that has been designed for heavy industrial and construction applications. Known for its robust performance and advanced features, this equipment is well-suited for demanding working environments.

One of the standout features of the UIG1313 is its powerful engine. It is equipped with a high-performance drive system that ensures optimal efficiency while minimizing fuel consumption. This not only enhances productivity but also reduces operational costs, making it an economical choice for businesses.

The UIG1313 boasts an impressive lifting capacity, allowing operators to handle heavy loads with ease. This capability is complemented by its advanced hydraulic system, which provides smooth and precise control while lifting or lowering materials. The responsive hydraulic functions significantly enhance the machine's versatility and make it suitable for various tasks, from material handling to construction.

Safety is a top priority for Liebherr, and the UIG1313 incorporates a range of safety features designed to protect both the operator and the equipment. These include an advanced anti-tipping system that ensures stability during operation and an intuitive control panel that provides real-time data on the machine's status.

Technologically, the UIG1313 is equipped with Liebherr's innovative telematics system. This technology allows for remote monitoring of the machine’s performance, enabling operators to track usage and maintenance needs effectively. By providing real-time insights, businesses can schedule maintenance proactively, reducing downtime and increasing productivity.

The machine’s ergonomic design enhances operator comfort, which is crucial for long working hours. The cabin is spacious, with excellent visibility and user-friendly controls that facilitate easier operation. Additionally, the UIG1313 features noise reduction technology, promoting a quieter work environment.

In terms of durability, the UIG1313 is built using high-quality materials that withstand the rigors of heavy use. The chassis is reinforced, providing exceptional stability and resistance against wear and tear. This robust construction ensures a longer lifespan, making it a wise investment for any fleet.

Overall, the Liebherr UIG1313 combines performance, safety, and advanced technology, making it a reliable choice for industries that require efficient and effective heavy machinery. It stands out in the market for its ability to adapt to various tasks while delivering consistent results. Whether used in construction, logistics, or other sectors, the UIG1313 remains a preferred option for professionals seeking quality and dependability.