Liebherr 7084376 - 03 Insertion into a row of kitchen units, Transporting the appliance

Page 6

Putting into operation

4.2 Insertion into a row of kitchen units

(1)

Stack cabinet

(3)

Fig. 9

Kitchen cabinet

(2)

Appliance

(4)

Wall

The appliance can be inserted into a row of kitchen units. To match the appliance Fig. 9 (2) to the height of the row of units, a suitable stack cabinet Fig.9 (1) can be fitted above the appliance. When inserting the appliance into a row of standard kitchen units (max. depth 580 mm), the appliance can be installed directly next to the kitchen unit Fig. 9 (3). The appliance door projects relative to the front of the kitchen unit by 34 mm at the side and by 50 mm in the middle of the appliance. It can be opened and closed perfectly as a result.

Important for the ventilation:

-At the back of the stack cabinet there has to be a ventilation duct of at least 50 mm depth throughout the width of the stack cabinet.

-The ventilation space under the ceiling has to be at least 300 cm2.

If the appliance is installed with the hinges next to a wall Fig. 9 (4), the distance between appliance and wall has to be at least 36 mm. This corresponds to the projection of the handle when the door is open.

4.3 Transporting the appliance

CAUTION

Risk of injury and danger of damage as a result of incorrect trans- port!

u Transport the appliance in a packed condition. u Transport the appliance upright.

u Do not transport the appliance without assistance.

4.4 Installing the appliance

In the event that the appliance is damaged, contact the supplier immediately before connecting to the mains.

The floor at the site must be flat and level.

Do not install the appliance in a location where it is exposed to direct radiation of the sun, next to a cooker, heater and similar. Always install the appliance directly against the wall.

Do not install the appliance without assistance.

Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m2 per 8 g of R 600a refrig- erant used in the appliance. If the room in which the appliance is installed is too small, a flammable gas-air mixture may form in the event of a leakage in the refrigeration circuit. The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance.

WARNING

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause short circuits.

u The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.

WARNING

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flammable. Escaping refrigerant may ignite.

u Do not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

u Do not place appliances emitting heat e.g. microwaves, toasters etc. on the appliance!

WARNING

Fire hazard and risk of damage due to blocked ventilation grille! u Always keep the ventilation grille free. Always ensure that the

appliance is properly ventilated.

u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because other- wise there will be vibratory noise!

u Remove the protective film from the outside of the appli- ance.*

NOTICE*

The stainless steel doors are provided with a high-quality surface coating and must not be treated using the accompanying care product.

Otherwise the surface coating will be affected.

u Wipe the coated door surfaces using a soft, clean cloth only. u Apply a stainless steel cleaner only to the stainless steel side walls evenly, wiping with the grain. Subsequent cleaning

becomes easier as a result.

u Wipe side walls with a paint finish using a soft, clean cloth only.

u Remove the protective film from the decorative trims and drawer fronts.*

u Remove all transit supports.

u Dispose of packaging material (see 4.5) .

NOTICE

Risk of damage due to condensate!

u Do not install the appliance directly alongside a further refrig- erator/freezer.

u Align the appliance so that it stands firmly and on a level by applying the accompanying spanner to the adjustable- height feet (A) and using a spirit level.

u Then support the door: Extend the adjustable foot at the turn hinge (B) until it rests on the floor and then make a further 90° turn.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operating instructions Contents Appliance at a glanceAppliance at a glance External dimensions of the appliance General safety informationGeneral safety information ConformityControls and displays Controls and displaysPutting into operation Putting into operation Transporting the appliance Installing the applianceInsertion into a row of kitchen units Stack cabinetControl Control3 Fan Setting the temperatureUsing the sectioned shelf Relocating the shelvesFreezer compartment Cold storage accumulators IceMakerCleaning the appliance MaintenanceMaintenance Cleaning the IceMakerMalfunction Customer serviceMalfunction Changing the interior light with bulbDecommissioning Switching off the applianceTaking the appliance out of service DecommissioningDisposing of the appliance

7084376 - 03 specifications

The Liebherr 7084376 - 03 is a cutting-edge component designed to enhance the performance and efficiency of Liebherr's extensive range of machinery. Known for its commitment to innovation, Liebherr integrates advanced features and technologies into its products, making the 7084376 - 03 a notable example of this endeavor.

One of the primary features of the Liebherr 7084376 - 03 is its robust construction, ensuring durability and reliability even in the most demanding working conditions. The material selection is paramount, with high-grade alloys used to withstand wear and tear, ensuring a long service life. This durability translates to reduced maintenance costs and increased uptime for users.

The 7084376 - 03 is equipped with state-of-the-art technologies that enhance its operational capabilities. One such technology is the advanced hydraulic system designed to optimize fluid dynamics. This system not only improves the efficiency of power transmission but also facilitates smoother operation, which is vital in handling heavy loads. Additionally, the hydraulic system is engineered to minimize energy consumption, making the machinery more eco-friendly.

Another significant characteristic of the Liebherr 7084376 - 03 is its innovative control interface. The user-friendly design allows operators to easily navigate through various settings and functionalities, promoting efficient use and quick adjustments as required. The interface is designed with intuitive visuals, ensuring that operators can focus on their tasks without getting bogged down by complex controls.

Moreover, the Liebherr 7084376 - 03 features advanced safety mechanisms. These include overload protection and automated alerts, which help prevent accidents and equipment failure. Safety is a crucial aspect of Liebherr’s design philosophy, and these features are a testament to their commitment to providing safe working environments.

In conclusion, the Liebherr 7084376 - 03 stands as a prime example of Liebherr's dedication to producing high-quality, innovative machinery components. Its robust construction, advanced hydraulic technologies, user-friendly control interface, and comprehensive safety features all contribute to its reputation as a reliable choice for operators. Whether in construction, mining, or other heavy-duty applications, the 7084376 - 03 is engineered to perform, ensuring efficiency and safety in challenging environments. As Liebherr continues to push technological boundaries, components like the Liebherr 7084376 - 03 are essential for achieving peak operational excellence.
Top Page Image Contents