Rangemaster 60S manual Cleaning Safety, Surface Cleaning

OVEN CLEANING

CLEANING SAFETY

Turn off all controls and wait for appliance parts to cool before touching or cleaning them. Clean appliance with caution. Use care to avoid steam burns if a wet sponge or clothe is used to wipe spills on a hot surface. Some cleaners can produce noxious fumes if applied to a hot surface.

SURFACE CLEANING

This is easily done using a damp cloth and a non-abrasive detergent, wipe using a soft dry cloth. For stainless steel parts with stubborn soils, use only plastic scrubbing pad or a sponge with vinegar and warm water. For Oven cooking cavity cleaning, follow the same procedure mentioned above, but to ease the cleaning you may start cleaning when the cooking cavity is still warm enough to be touched.

WARNING: Do not use steam cleaners to clean any part of the oven.

OVEN DOOR: To remove and replace the Oven Door, please follow procedures here below;

REMOVING OVEN DOOR ON 60S MODELS: Fig. 5

Fully open the oven door. – Raise the U-clip over the hook on each of the hinges to the “locked” position, see figure 5 and 6. This will prevent the hinge from snapping closed when the door is removed. – Grasp the door by the sides toward the back. – Raise the front of the door several centimetres (there will be some spring resistance to overcome because of the hinge being locked). – When the front of the door is high enough, you will be able to lift the hinges to clear the indents. – Pull the hinges out of the slots in the oven front frame.

TO REPLACE THE OVEN DOOR ON 60S MODELS: Fig. 5

Grasp the sides of the door at the centre and inert the ends of the hinges into the slots in the oven front frame as far as they will go, see figure 5 and 6. – With the door open all the way, lower the two locking clips. – Raise the oven door and make sure that it fits evenly with the front sides.

REMOVING OVEN DOOR ON 90D MODELS: Fig. 6

Open the door for about 45°. Step 1: With thumbs push levers “T” to bottom of the hinges. Step 2: Keeping levers “T” down, lower the door till you hear the click when the “T” levers are locked and so blocking the hinges.

Step 3: Making sure “T” levers are locked, partially close the door to about 60°. Step 4: With the forefinger lift the “Z”

levers of both hinges. Step 5 and 6: Lift the door and take out as shown in fig. 6.

TO REPLACE THE OVEN DOOR ON 90D MODELS: Fig. 6

Grasp the door by the sides and insert hinges into their slots, keeping “Z” levers up (as in step 4). Hook the hinges into their locations by following steps 6 and 5 backwards. Once “Z” levers are in place, fully the open door to unlock “T” levers. Once “T” levers are in the up-right position, gently close the door.

WARNING. Never release the U-clip or T-clip levers when the door is off. Do not close the hinges without the weight of the door, the powerful springs will snap the hinges closed with great force.

CAUTION: Do not place excessive weight on or stand on an open oven door. This could break the door or injure the user. Also, do not attempt to open or close door or operate oven until door is properly replaced.

REPLACING THE OVEN LIGHT

WARNING; To prevent electrical shock and/or personal injury read follow this procedure: Before replacing the light bulb, be sure the electric power is turned off at the circuit breaker. Be sure the oven and light bulb are cool. Then remove light cover A by unscrewing it. Figure 7. Do not touch hot bulb with a damp cloth as this may cause the bulb to break.

Replace light bulb with a 25 W for 230 V a.c. appliance bulb only. Figure 7.

If the light cover is damaged or broken, do not use the oven until a new cover is in place. Do not operate the oven unless the light cover is securely in position.

4 9880015700 E OVEN RANGEMASTER 03-2006