Peavey 115P Volume Control Adjustment, Adjusting the kosmos Processing Level, High-Pass Outputs

Page 8

Volume Control Adjustment

The Impulse 115P is equipped with a Master System Level volume control (6). When the Master System Level is adjusted fully clockwise‚ gain is at maximum and the input sensitivity is 0.375 VRMS for full-rated output. When this control is set half way up‚ gain is unity and 1.5 VRMS will drive the system to full power output. When driving the Impulse 115P from a mixer‚ it may be advantageous to reduce the input sensitivity by turning the volume control to the half-way point. At this setting‚ the Impulse 115P will more closely match a typical power amp input.

The amplifiers in the Impulse 115P are equipped with DDT. This unit also includes an LED (11) that illuminates when DDT is activated. This LED is located next to the Master System level. The DDT circuit will automatically reduce the channel gain to a level just slightly into clipping, guarding the speakers against the damaging high power continuous square waves that may be produced. Situations that may activate the DDT circuit include uncontrolled feedback, oscillations, or an improper equipment setting or malfunction upstream from the amplifier.

Always turn on any peripheral units before turning on the Impulse 115P. Also‚ make sure the Master System level is completely down (CCW) before turning the unit on.

Adjusting the kosmosProcessing Level

The amount of kosmos processing is controlled by the Master System level knob. In order to achieve more sub-harmonic processing‚ turn the Master System level (6) up and the Level/Quake knob (7a) down.

When using the Impulse 115P with a passive‚ full-range speaker system‚ the relationship between the Master System level and the Quake/Sub level will determine the balance between the overall subwoofer output and the high frequencies that sent to the Left and Right speaker outputs. The amount of kosmos processing can not be controlled independently. It can‚ however‚ be bypassed using the Bypass switch (7c).

When using the Impulse 115P with a powered‚ full-range speaker system from the line level‚ high-pass outputs (8)‚ the powered‚ full-range speakers will usually have their own volume control. This will allow the high frequency level to be set independently. However‚ the kosmos Xpanse control (7b) for adjusting stereo spread‚ can only be adjusted at the Impulse 115P subwoofer.

High-Pass Outputs

These are low impedance‚ filtered outputs that are provided to send the high frequencies to a powered speaker or to a conventional power amp and speaker system. The output level is set by the Master System level control on the Impulse 115P.

The nominal polarity of these outputs is positive (pin 2) and can be run directly into most full-range‚ powered speaker systems.

If you experience hum or related ground loop problems‚ it might help to lift the shield ground on the balanced XLR cable at the Impulse 115P end. This can be accomplished via the convenient ground lift switch (10b) located underneath the High-pass output jack group. Check any input changes carefully. Always turn the volume control down before plugging and unplugging cables or switching ground lift switches.

Left & Right Outputs

These outputs will supply a full-range‚ 8 ohm minimum speaker system with a high-passed amplifier signal when using the Impulse 115P as a 3-piece system. The Xpanse control (7b) will expand the stereo sound stage and add high frequency processing to these outputs.

Impulse 115P: Subwoofer only (Add-on Use)

When using the Impulse 115P as a powered subwoofer only‚ run a full-range stereo signal to the inputs (5) or plug a mono signal into the Left input (5a) and engage the Mono switch (5d). The subwoofer will reproduce frequencies from approximately 45 Hz–120 Hz.

8

Image 8
Contents Impulse 115P Powered Subwoofer · Operations Manual Page Important Safety Instructions Sound Level dBA, Slow ResponseFeatures DescriptionIEC Power Cord Connection FusePower Switch Power LEDSpeaker Level Powered Outputs Ground Lift SwitchesGetting a Signal to the Impulse 115P Using the Pole Stand BaseAC Power Volume Control Adjustment Adjusting the kosmos Processing LevelHigh-Pass Outputs Left & Right OutputsTroubleshooting Hum or Buzz Rattling or BuzzingExcessive High-Frequency Output from the Subwoofer Male Vocals Sound Muddy or BoomyCare & Maintenance CleaningSunlight/Heat TouchupHookup Diagrams Live Application Non-powered Mixer Add-on Use DJ Application Channel Stereo Operation Page 115P Block Diagram Frequency Response Curves THD & IM Beschreibung Netzbetriebener SubwooferMerkmale A R P a N E L Power-Schalter Power-LEDIEC-Netzkabelanschluss EingängeVorsichtsmaßnahmen Page Page Left/Right Outputs Fehlersuche Page Page Frequency Response Curves Spezifikationen Características DescripciónFusible Conexión del cable de corriente IECInterruptor de Corriente LED de CorrienteEntradas Nivel Maestro del SistemaPrecauciones Usando la Base de AtrilAjuste DE Control DE Volumen Ajuste del Nivel de Proceso del kosmosSalidas de Agudos Salidas Izquierda y DerechaImpulse 115P Sistema Estéreo de 3 Canales Impulse 115Ps con 2 Parlantes de Rango CompletoMúltiples Impulse 115P u otros productos amplificados AplicacionesRuidos Vibraciones ExternasLa Voz Masculina Suena Muy Grave y Lodosa Sonido Distorsionado o SucioCuidado Y Mantenimiento Calor/Luz del solLimpieza RetoquesFrequency Response Curves Especificaciones Caractéristiques Connecteur d’Alimentation IEC Interrupteur d’AlimentationEntrées Alimentation électrique Envoyer un Signal à votre Impulse 115PUtiliser l’Adaptateur de Pole Contrôle de Volume Ajustez les contrôles du kosmosSorties Hautes-Fréquences High-Pass Sorties Droite & GauchePas de Signal en Sortie Impulse 115P Système Stéréo 3-EnceintesImpulse 115Ps avec 2 Enceintes Satellites Utilisation de Multiple Impulse 115PMaintenance Saturation/Craquement de Haut-parleurSorties Excessives de Hautes Fréquences du Caisson Sub Voix d’Hommes avec Trop de Dynamique dans les GravesAccastillage de fixation Exposition au soleil/ChaleurNettoyage Frequency Response Curves Impulse 115P Peavey Electronics Corporation Limited Warranty Product Category80304936

115P specifications

The Peavey 115P is a robust and versatile powered speaker designed to meet the demands of various live sound and monitoring applications. Renowned for its compatibility with a range of audio systems, the 115P is an essential tool for musicians, DJs, and audio professionals looking for reliable performance and clarity.

At the heart of the Peavey 115P is its 15-inch woofer, which delivers powerful bass response and rich mids, making it suitable for everything from music performances to public speaking engagements. This woofer is complemented by a high-frequency compression driver that ensures crisp, articulate highs, blending seamlessly with the low-end sound to provide a well-rounded audio experience.

One of the standout features of the Peavey 115P is its integrated power amplifier, which boasts a substantial output. This amplifier eliminates the need for external power sources, making setup quicker and easier. Additionally, the speaker's onboard controls include a master volume knob and EQ settings, giving users fine control over their sound.

The 115P employs Peavey’s patented Circuitry, including Volume and Equalization controls that enhance overall sound quality. The speaker also incorporates a discrete Class D amplifier section, known for its efficiency and lightweight design, ensuring that the 115P not only sounds excellent but is also easy to transport.

Connectivity is another strong suit of the Peavey 115P. It features balanced XLR inputs, making it easy to connect to a variety of devices, including mixers and microphones. The speaker also includes a loop-through output for daisy-chaining additional speakers, allowing for expanded coverage in larger venues.

Constructed with durability in mind, the Peavey 115P is housed in a rugged enclosure that stands up to the rigors of touring and frequent transport. Its design includes integrated handles for easy lifting and maneuvering, and its lightweight profile adds to its portability.

In summary, the Peavey 115P is a powerful, flexible speaker system that excels in delivering high-quality audio performance for a variety of applications. With its impressive features, reliable technology, and durable construction, it is an excellent choice for both professional and amateur sound engineers looking for outstanding sound reinforcement. Whether you are performing at a small venue or using it for a large event, the Peavey 115P is engineered to meet your sound needs effectively.