Hoover HEDS 668S-80, HEDS 668-80 manual Fastened tightly in place, Efficiency slightly reduced

Page 13

 

Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is

 

fastened tightly in place.

 

If the water pipes are new or have not been used for an extended period of time, let the water

 

run to make sure t hat the water is clear and free of impurities. If this precaution is not taken,

 

there is a risk that the water inlet can get blocked and damage the appliance.

 

 

 

The water supply to the appliance can also be connected to the house hot water line

 

(centralized system, heating system),as long as it does not exceed a temperature of 60 C.

Con nector of ModelⅡ

In this case, the wash cycle time will be shortened by about 15 minutes and the wash

efficiency slightly reduced.

 

 

The connection must be made to the hot water line following the same procedures as those

 

for the connection to the cold water line.

Position the appliance in the desired location. The back should rest against the wall behind it, and the si des, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to

facilitate proper installation.

Once the appliance is positioned,adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level. In any case ,the appliance should not be inclined more than 2 .

Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance. The free end of the hose must be at a height between 40 and 100cm and must not be immersed in water.

If the sink is 34 or higher from the floor, the excesswater in Unicouple hoses cannot be drained directly into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container that is heldoutside and lower than the sink.

450

DIMENSIONS(mm)

850

580

1135

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Heds 668-80/HEDS 668S-80 Before calling for service ,13 „ Do not tamper with controls Coarse Filt er Silverware BasketFor the cycle Press the Start/Reset button to start the washingPause RunAuto nomy 14-28Gram/cycle If only four settings we suggest you to set on Page Serving spoon Never run the dishwasher without the filters in place UncrewPage Page Efficiency slightly reduced Fastened tightly in placeFor the connection to the cold water line Fuse blown, or Power supply is notCircuit breaker acted Turned on Closed securelyTo remove the stains by hand Detergent Tea or coffee stainsWill happen Iron deposits in water

HEDS 668S-80, HEDS 668-80 specifications

The Hoover HEDS 668-80 and HEDS 668S-80 are advanced sensor modules widely recognized for their precision and reliability in various applications. Both models serve prominently in the realm of motion detection and optical encoders, making them indispensable in robotics, industrial automation, and consumer electronics.

At the core of these sensors is the use of integrated photodetectors and light emitters, which work together to accurately capture motion data. The HEDS 668-80 features a compact design, allowing for easy integration into numerous hardware configurations. It incorporates a dual-channel output, which provides both quadrature and single-ended output signals. This feature enables enhanced motion control and allows for more accurate detection of direction, making it suitable for applications requiring precise angular measurements.

One of the standout technologies in the HEDS series is its use of reflective optical sensing. This technology minimizes interference from ambient light conditions, ensuring reliable performance even in varying environmental settings. The sensors are designed with a resolution of up to 500 counts per revolution, allowing for finely-tuned control in robotic applications.

The HEDS 668S-80 enhances the capabilities found in the 668-80 model by offering an increased tolerance for temperature variations and shock resistance. This makes it an ideal candidate for harsh operating conditions, where reliability is paramount. The HEDS 668S-80 also boasts an improved response time, further enhancing the performance in high-speed applications.

Both models feature a straightforward mounting system that facilitates installation and adjustment, allowing engineers to set up their systems quickly and efficiently. Additionally, their robust construction ensures durability across extended periods of use, providing a long lifespan in demanding applications.

In summary, the Hoover HEDS 668-80 and HEDS 668S-80 represent advanced sensor technology that combines high performance with robust design. Their integrated features cater to a variety of applications, making them a vital component in the ever-evolving landscape of automated systems and precision measurement. As industries increasingly rely on automation, these sensors offer the reliability and accuracy that engineers need to achieve optimal performance in their projects.
Top Page Image Contents