Hoover HEDS 668-80, HEDS 668S-80 manual 14-28, Auto nomy, Gram/cycle

Page 6

If your model have not water softener, you may skip this section.

There are two ways to reduce the water hardness: one way is using water softener, the other is using detergent.

The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.

The appliances is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.

Always use salt intended for use with dishwashers.

The salt container is located beneath the lower rack and should be filled as follows:

1 Remove the lower basket and then unscrew and remove the cap from the salt container.

2 If you are filling the container for the first time ,fill 2/3 of its vol ume with water.

3 Place the end of the funnel(supplied) into the hole and introduce about 2kg of salt .It is norm al for a small amount of wat er to come out of the salt container

4 Carefully screw the cap back on.

1. The salt container must be refilled when the salt w arning li ght comes on. Though the salt container is filled enough, t he indicator light may not black out before the salt fully dissolve.

2. If there are spills of the salt, a soak program could be run to wipe them out.

The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize and customize the level of salt consumption so that the salt consumption could be set proceed as follows:

1

2

Unscrew the cap from the salt container.

There is a ring on the container with an arrow on it (see Figure to the side), if necessary, rotate the ring in the anticlockwise directi on from the "-" Setting

toward the "+" sign, based on the hardness of the water being used.It is recommended that adjustments should be made in accordance with the following schema:

°fH

0~10 10~25 25~50

>50

WATER HARDNESS

dH

0-5

5-14

14-28

>28

 

Selector

Salt consumption

Auto nomy

mmol/l

Position

(gram/cycle)

(cycles/2kgs)

0-1.0

-

0

/

1.0-2.5

/

20

60

2.5-5.0

MED

40

40

 

+

 

 

>5.0

60

25

Contact your local water board for information on the hardness of your water supply.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Heds 668-80/HEDS 668S-80 Before calling for service ,13 „ Do not tamper with controls Silverware Basket Coarse Filt erPause Press the Start/Reset button to start the washingFor the cycle Run14-28 Auto nomyGram/cycle If only four settings we suggest you to set on Page Serving spoon Uncrew Never run the dishwasher without the filters in placePage Page Fastened tightly in place Efficiency slightly reducedFor the connection to the cold water line Circuit breaker acted Power supply is notFuse blown, or Turned on Closed securelyWill happen Detergent Tea or coffee stainsTo remove the stains by hand Iron deposits in water

HEDS 668S-80, HEDS 668-80 specifications

The Hoover HEDS 668-80 and HEDS 668S-80 are advanced sensor modules widely recognized for their precision and reliability in various applications. Both models serve prominently in the realm of motion detection and optical encoders, making them indispensable in robotics, industrial automation, and consumer electronics.

At the core of these sensors is the use of integrated photodetectors and light emitters, which work together to accurately capture motion data. The HEDS 668-80 features a compact design, allowing for easy integration into numerous hardware configurations. It incorporates a dual-channel output, which provides both quadrature and single-ended output signals. This feature enables enhanced motion control and allows for more accurate detection of direction, making it suitable for applications requiring precise angular measurements.

One of the standout technologies in the HEDS series is its use of reflective optical sensing. This technology minimizes interference from ambient light conditions, ensuring reliable performance even in varying environmental settings. The sensors are designed with a resolution of up to 500 counts per revolution, allowing for finely-tuned control in robotic applications.

The HEDS 668S-80 enhances the capabilities found in the 668-80 model by offering an increased tolerance for temperature variations and shock resistance. This makes it an ideal candidate for harsh operating conditions, where reliability is paramount. The HEDS 668S-80 also boasts an improved response time, further enhancing the performance in high-speed applications.

Both models feature a straightforward mounting system that facilitates installation and adjustment, allowing engineers to set up their systems quickly and efficiently. Additionally, their robust construction ensures durability across extended periods of use, providing a long lifespan in demanding applications.

In summary, the Hoover HEDS 668-80 and HEDS 668S-80 represent advanced sensor technology that combines high performance with robust design. Their integrated features cater to a variety of applications, making them a vital component in the ever-evolving landscape of automated systems and precision measurement. As industries increasingly rely on automation, these sensors offer the reliability and accuracy that engineers need to achieve optimal performance in their projects.
Top Page Image Contents