Indesit DIS 04 operating instructions Rinse aid and refined salt, Measuring out the rinse aid

Rinse aid and refined salt

Only use products which have been

number 2).

EN

specifically designed for dishwashers.

E.g. Hardness level 1 (1st cycle indicator light flashing)

Do not use table salt or industrial salt, or

Hardness level 2 (1st cycle indicator light ON, 2nd cycle

washing up liquid.

indicator light flashing)

Hardness level 3 (1st and 2nd cycle indicator lights ON, 3rd

Follow the instructions given on the packaging.

cycle indicator light flashing etc) up to maximum 5 levels.

If using a multi-functional product it is not necessary to

- Press the P button repeatedly until the desired hardness

add rinse aid; however, we recommend that you add salt,

level has been reached (1-2-3-4-5*see Water hardness

especially if you live in an area where the water is hard or

table).

very hard. Follow the instructions given on the packaging.

- To exit the function, wait approximately 30 seconds or switch

If you do not add salt or rinse aid, the LOW

off the machine using the ON/OFF button.

SALT* and LOW RINSE AID* indicator lights

Even if using multi-functional tablets, the salt dispenser should

remain lit.

still be filled.

Measuring out the rinse aid

Water Hardness Table

Rinse aid makes it easier for the crockery to dry, as water

°dH

°fH

mmol/l

level

0

11

0

20

1.1

2

1

runs off surfaces more readily and therefore does not leave

12

17

21

30

2.1

3

2

streaks or marks.

17

34

31

60

3.1

6

3

The rinse aid dispenser should be filled:

34

50

61

90

6.1

9

4*

• When the LOW RINSE AID* indicator light on the control

For values between 0°f and 10°f, we do not

panel is illuminated;

recommend the use of salt.

1. Open the dispenser by turning

* this setting may cause a slight increase in the

the lid (G) in an anticlockwise

duration of the cycle.

direction.

(°dH = hardness measured in German degrees - °f =

2. Pour in the rinse aid, making

sure it does not overflow from the

hardness measured in French degrees - mmol/l = millimoles

F

dispenser. If this happens, clean

per litre)

the spill immediately with a dry

Measuring out the refined salt

G

cloth.

In order to achieve the best possible results using a wash

3. Screw the lid back on.

cycle, make sure that the dispenser is never empty. Refined

NEVER pour the rinse aid directly into the appliance tub.

salt removes limescale from the water, thus avoiding the

Adjusting the amount of rinse aid

formation of deposits on crockery.

The salt dispenser is located in the lower part of the

If you are not completely satisfied with the drying results, you

dishwasher (see Description) and should be filled:

may adjust the quantity of rinse aid used. Use a screwdriver

• When the green float* cannot be seen by simply looking at

to turn the dosage adjuster (F) to one of the 6 pre-set

the cap of the salt dispenser.

positions (the default position is set to 4):

• When the LOW SALT* indicator light on the control panel is

• If there are streaks on the crockery, set the adjustment

illuminated;

device to a lower number (1-3).

1. Remove the lower rack and unscrew

• If drops of water remain on the crockery or if there are

the container cap (anticlockwise).

limescale marks present after the cycle has finished, set the

2. The first time you do this: fill the water

adjuster to a higher number (4-6).

tank right up to its edge.

Setting the water hardness

3. Position the funnel* (see figure) and

fill the salt container right up to its edge

Every dishwasher is equipped with a water softener which, by

(this should hold approximately 1 kg); it is not unusual for a

using refined salt designed especially for this type of

little water to leak out.

appliance, supplies water without limescale which is then used

4. Remove the funnel* and wipe any salt residue away from

to wash the crockery.

the opening; rinse the cap under running water and then

This dishwasher offers a setting which helps to reduce

screw it on, the head facing downwards so as to let the water

pollution and optimises washing performance in accordance

flow out of the four cracks which are arranged in a star shape

on the lower part of the cap. (Salt cap with green float*)

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

It is advisable to perform this procedure every time you

household with water.

add salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

- Open the door and switch on the machine by pressing the

can get into the container during the wash cycle (this could

ON/OFF button.

- Press the P button and hold for approximately 5 seconds;

damage the water softener beyond repair).

two short beeps will sound and the indicator light

When necessary, measure out the salt before a wash

corresponding to the set degree of hardness will flash slowly

cycle so that any saline solution which has leaked out of the

on the control panel (the water softening system is set to

salt dispenser is removed.

* Only available in selected models. 9