Fitting the cooktop above an oven

Installation

When installing the cooktop above an oven, both the electric- ity supply cable and the gas pipe or ﬂexible hose must not touch hot parts of the oven housing.

When installing above a built-under oven without forced cool- ing ventilation, suitable air vents should be provided for as shown in the ﬁgure (inlet at least 200 cm² from the bottom, outlet at least 120 cm²

from the top part) to allow adequate ventila- tion inside the housing unit.

Also a wooden panel “A” should be installed beneath the hob as in- sulation, positioning it at a minimum distance of 15 mm from the hob housing

200 cm²

Gas connection

Electrical connection

The electrical supply for the cooktop must be a 240 Volt 50 Hz.

The fuse and electrical wiring of the home/premises must support the load of the appliance.

The appliance must be earthed. A 3 pin ﬂexible power cord is supplied with the appliance to allow the cooktop to be connected to a properly earthed and rated power socket.

The ﬂexible cord of the appliance must not be subject to direct heat and must be positioned after installation of the appliance so that its temperature does not exceed 75°C.

IMPORTANT If a power socket needs to be installed or relocated, the work must be done by a licensed electrician.

Gas type conversion

If the hob is to be converted for use with a type of gas other than that for which it was set in the factory (indicated on the cooktop data plate), the burner injectors must be replaced as follows:

Remove the pan supports and the burners.

Unscrew the injectors (“A” in ﬁugure below) using a 7 mm socket wrench, and replace them with injectors of suitable oriﬁce diameter, as indicated on the appliance data plate.

Reassemble the parts.

This appliance is suitable for use with either a ﬂexible con- nection or rigid copper connection. If installing the appliance with a ﬂexible connection, the ﬂexible connection must be approved to class B or D of AS/NZS1869 as a minimum.

Fit regulator supplied for Natural Gas (if applicable) at rear of appliance, and as close as practicable to the appliance.

It is recommended that an isolating valve and union be

ﬁtted, to enable simple disconnection for servicing. These are to be in an accessible location.

Flexible hose

If a ﬂexible hose is used, it should be as short as possible with a maximum length of 1.5 metres;

it should not be bent or kinked;

it should not be in contact with the rear wall of the appli- ance or in any case with parts which may reach a tem- perature of 50°C;

it should not come into contact with pointed parts or sharp corners;

it should be easy to inspect along its entire length in order to be able to check its condition.

The supply connection point must be accessible with the appliance installed.

If a regulator is required for the new gas type, instal an ap- proved regulator of appropriate pressure setting and ﬂow capacity.

Replace the gas type label with one suitable for the new gas type.

Perform the post installation checks as described later in this manual. In particular, check the turn down setting of each burner and adjust where necessary.

Perform post installation checks and ensure proper and safe operation before leaving. Test all burners individually and in combination.

PZ 750R GH NG, PZ 640T GH NG specifications

Indesit, a renowned brand in home appliances, presents two remarkable gas cookers: the Indesit PZ 640T GH NG and the PZ 750R GH NG. These models stand out for their efficiency, advanced features, and user-friendly design, making them ideal for both amateur cooks and seasoned chefs alike.

The Indesit PZ 640T GH NG is a compact and versatile model featuring four gas burners, offering ample cooking space for various dishes. This stove provides a perfect combination of power and precision with its high-efficiency burners designed to reduce cooking time while ensuring even heat distribution. The easy-to-use knobs allow the user to adjust the flame to their desired level quickly. Equipped with a durable enamel finish, this cooker is not only stylish but also easy to maintain, keeping your kitchen looking pristine.

On the other hand, the Indesit PZ 750R GH NG takes things a step further with a larger cooking surface, featuring five gas burners. This extra burner provides additional flexibility, making it perfect for preparing complex meals that require multiple pots. The intelligent burner layout ensures that pots of various sizes can be fitted comfortably. The PZ 750R GH NG is designed for energy efficiency, allowing you to save on gas while enjoying high cooking performance.

Both models feature an automatic ignition system, which provides a quick and safe way to start cooking. The integrated safety devices ensure that gas flow is interrupted if the flame goes out, offering peace of mind for users. Additionally, the oven compartments in these models boast even heating technologies that enhance the cooking experience and ensure that your dishes are cooked to perfection.

With a sleek design and various color options, the Indesit PZ 640T GH NG and PZ 750R GH NG can complement any kitchen décor. The availability of easy-to-clean surfaces and removable burners make maintenance hassle-free, allowing users to spend more time enjoying their culinary creations rather than worrying about cleanup.

In conclusion, whether you choose the compact PZ 640T GH NG or the more spacious PZ 750R GH NG, both cookers embody Indesit's commitment to quality and performance. With their innovative features and user-centric designs, they promise to elevate your cooking experience and meet the demands of everyday meal preparation with ease and reliability.

Installation