Service Details, Post installation checks

Service Details

Post installation checks

Leak Check

Ensure all gas control knobs are in the Off position.

Ensure the gas supply is switched on.

Spray a solution of soapy water onto all gas joints as well as the full length of any ﬂexible hoses.

UNDER NO CIRCUMSTANCES USE A NAKED FLAME IN CHECKING FOR LEAKS.

If bubbles appear anywhere, turn the gas supply off, check all connections and retest. If satisfactory operation cannot be achieved, contact place of purchase or their appointed agent for service.

Flame check

Turn each burner on, and ensure that the ﬂame is blue with minimal yellow tipping. If there is signiﬁcant yellow tipping, ﬂame lift off or excessive noise, check pressure and adjust at the regulator if necessary.

If satisfactory operation cannot be achieved, contact place of purchase or their appointed agent for service.

Igniter operation

Check that the igniter for each burner successfully ignites the gas.

If an igniter fails to work, ﬁrst remove the plug from the electrical power outlet, and then check that all the electrical connections are in place.

If satisfactory operation cannot be achieved, contact place of purchase or their appointed agent for service.

Low ﬂame setting

Check the low ﬂame setting for each hob burner to ensure that the minimum ﬂame will not be extinguished by air draughts.

Light the burner.

Turn the control until it engages in the minimum position.

Ensure the ﬂame is stable and will not be extinguished by air draughts.

To adjust the minimum ﬂame:

Follow the procedure described in the gas conversion in- struction.

DO NOT MODIFY THIS APPLIANCE IN ANY WAY.

Electrical equipment and components

To check or replace the ignition module

Electrical components are located below the hob surface. To access the components:

IMPORTANT: First ensure that gas and electrical power are disconnected before performing any service to this appliance.

Remove the control knobs, trivets, burner caps and burner head assembly.

Invert the cooktop and remove the two screws on the base near the gas manifold.

Lift the base upwards. Take care to ensure that no dam- age occurs to the spark ignition leads or the igniter com- ponents.

The electronic ignition module is now easily accessible for service or replacement.

Assembly is a reversal of the above procedure.

To check or replace the gas controls and gas manifold

Gas components are located below the hob surface.

Access the components underneath the surface of the hob as described in the previous section.

Disconnect all ancillary gas piping, wiring and any screws, as appropriate.

The gas manifold may then be extracted.

Replacement is a reversal of the above procedure.

ALWAYS PERFORM A LEAK CHECK AFTER PERFORM- ING ANY SERVICE. Correct procedure is at the top of this page.

Adjust turn down setting

Put the tap to the low ﬂame position;

Remove the tap knob and turn the adjusting screw, situ- ated inside the tap stem (ﬁg.11), using a screwdriver (loosening the screw increases the height of the ﬂame, tightening decreases it). note: the adjusting screw must be fully screwed down for liquid gas.

Having obtained the low ﬂame setting required and with the burner lit, abruptly change the position of the knob several times from minimum to maximum and vice versa and check that the ﬂame does not go out.

PZ 750R GH NG, PZ 640T GH NG specifications

Indesit, a renowned brand in home appliances, presents two remarkable gas cookers: the Indesit PZ 640T GH NG and the PZ 750R GH NG. These models stand out for their efficiency, advanced features, and user-friendly design, making them ideal for both amateur cooks and seasoned chefs alike.

The Indesit PZ 640T GH NG is a compact and versatile model featuring four gas burners, offering ample cooking space for various dishes. This stove provides a perfect combination of power and precision with its high-efficiency burners designed to reduce cooking time while ensuring even heat distribution. The easy-to-use knobs allow the user to adjust the flame to their desired level quickly. Equipped with a durable enamel finish, this cooker is not only stylish but also easy to maintain, keeping your kitchen looking pristine.

On the other hand, the Indesit PZ 750R GH NG takes things a step further with a larger cooking surface, featuring five gas burners. This extra burner provides additional flexibility, making it perfect for preparing complex meals that require multiple pots. The intelligent burner layout ensures that pots of various sizes can be fitted comfortably. The PZ 750R GH NG is designed for energy efficiency, allowing you to save on gas while enjoying high cooking performance.

Both models feature an automatic ignition system, which provides a quick and safe way to start cooking. The integrated safety devices ensure that gas flow is interrupted if the flame goes out, offering peace of mind for users. Additionally, the oven compartments in these models boast even heating technologies that enhance the cooking experience and ensure that your dishes are cooked to perfection.

With a sleek design and various color options, the Indesit PZ 640T GH NG and PZ 750R GH NG can complement any kitchen décor. The availability of easy-to-clean surfaces and removable burners make maintenance hassle-free, allowing users to spend more time enjoying their culinary creations rather than worrying about cleanup.

In conclusion, whether you choose the compact PZ 640T GH NG or the more spacious PZ 750R GH NG, both cookers embody Indesit's commitment to quality and performance. With their innovative features and user-centric designs, they promise to elevate your cooking experience and meet the demands of everyday meal preparation with ease and reliability.