Multiquip MVH406DSZ Before Starting, Checking Engine Oil Level, Checking the Hydraulic Oil Level

Page 16

INSPECTION

Before Starting

1. Read safety instructions at the beginning of manual.

2.Familiarize yourself with the operating and control elements of the machine and the working environment. This includes obstacles in the working area, bearing capacity of the ground and the necessary safety provisions.

3.Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

4.Check fastening nuts and bolts for tightness. Loose threads may cause damage to the machine when vibrating.

5.Understand the geographical features and regulations of the job site.

6.Clean the compactor, removing dirt and dust. Particularly, the bottom of the plate, engine cooling air inlet.

Checking Engine Oil Level

1.To check the engine oil level, place the compactor on secure level ground with the engine stopped.

2.Remove the dipstick from the engine oil filler hole (Figure 4) and wipe it clean.

3.Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

Figure 5. Engine Oil Level

Table 4. Oil Tyoe

Season

Temperature

Oil Type

 

 

 

Summer

25°C or Higher

SAE 10W-30

 

 

 

Spring/Fall

25°C~10°C

SAE 10W-

30/20

 

 

Winter

0°C or Lower

SAE 10W-10

 

 

 

Checking the Hydraulic Oil Level

1.To check the engine oil level, place the compactor on secure level ground with the engine stopped.

2.Remove the hydraulic oil breather cap located at the top of the hydraulic oil tank (Figure 6).

3.Using a 24 mm wrench, remove the hydraulic oil filler plug.

4.Visually inspect to determine if hydraulic oil level is low. If oil level is low add Shell Tellus 32 hydraulic oil or equivalent through the hand pump oil filler port.

OIL

BREATHERTANK

CAP

Figure 4. Engine Oil Dipstick Removal

4.If the oil level is low (Figure 5), fill to the edge of the oil filler hole with the recommended oil type (Table 4). Maximum oil capacity is 1.16 quarts (1.10 liters).

HYDRAULIC

OIL PLUG

(24 MM WRENCH)

Figure 6. Hydraulic Oil Filler Plug Removal

page 16 — mvh406dsz/dsCPAs pLATE COMPACTOR • operation and parts manual — rev. #7 (02/28/14)

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Series Model MVH406DSZ/ MVH406DSCPAS PROPOSITION 65 Warning Diesel engine exhaust and somePage Table of Contents MVH406DZ/DSCPAS Reversible Plate CompactorChoose from three easy options Safety Information Safety MessagesGeneRaL saFeTY Engine saFeTY Before servicing equipmentBaTTeRY saFeTY eLeCTRiC sTaRT OnLY FueL saFeTY„ Use well-insulated gloves when picking up the battery TRanspORTing saFeTY EnviROnmenTaL saFeTY/deCOmmissiOningEmissiOns inFORmaTiOn Emission Control LabelFuji Heavy Industries Dimensions MVH406DSZ/DSCPAS Reversible Plate Compactor DimensionsGeneral nformation Components MVH406DSZ/DSCPAS Reversible Plate Compactor ComponentsBasic engine Robin DieselUsing a 24 mm wrench, remove the hydraulic oil filler plug Before StartingChecking Engine Oil Level Checking the Hydraulic Oil LevelChecking the Air Cleaner Loosen the wing nut , remove the air cleaner coverChecking The Fuel Remove the fuel cap located on top of fuel tankAdjusting Handle Height OperationReleasing the Handle Electric Start OptionRecoil Start Place the throttle lever in the Start position centerNormal Shutdown Emergency ShutdownStowing the Handle Push up the handle upward until the handle locks in placeNormal Compaction Compaction Limit Compaction Sensor MVH406 Dscpas OnlySystem Diagnostics to Detect Operational Abnormalities Function to Detect Electric System AbnormalityMaintenance Inspection and Maintenance Service TablesDaily Service „„Check for leakage of fuel or oilEngine Oil Replacement Reinstalling the V-beltAir Filter Every 6 Months or 400 Hours Replacing the V-beltVibrator Oil Level Check Draining Vibrator OilDraining Hydraulic Oil Prevent dirt and dust from enteringAdding Hydraulic Oil Battery Maintenance OptionBleeder plug should only be loosened, but not removed Battery Charging Battery Cable Connection OptionTroubleshooting Trouble shooting compactor Trouble shooting engine Troubleshooting engineDipstick Explanation of Code in Remarks Column Suggested Spare Parts MVH-406 Nameplates and decalsDecal OIL SAE 10W-30 Decal Model Logo MVH-406Decal Caution Decal Shell Tellus OILVibrating Plate Assy Vibrating Plate OIL GaugeCopper Packing Packing 1/4 CUBase and Engine Assy Base Engine ASSY., 1B40Bolt 10X30T Belt Cover in L100Vibrator Assy Vibrating Case Roller Bearing NJ310EMC4Rotary SHAFT, Drive GEAR, DriveControl Handle Assy Handle Bracket Handle BracketrWASHER, Flat M12 Rubber CouplingControl Handle Assy Bolt 8X25 T Throttle LeverBAR GRIP, I.D MM COVER, Throttle LeverHand Pump Assy Accumlator Includes Items W/#Control Shaft BushBattery Assy Battery Cord 400L Battery Cord + 550LCRADLE, Battery Battery 46B24LCOMPACTION Analyzing System ASSY. mVH4O6DSCPAS Wire HARNESS, Sensor Wire HarnessCOVER,BATTERY Wire CLIP, SensorElectric Device Assy Buzzer EBL Wire CompleteIgnition KEY Robin D1B40T92040 Spare Parts KIT Assy 1000H MAINTE.KIT Gasket SET CRK.CASEEmergency KIT Robin D1B40T92040 Accessories Assy Accessories KIT Tool SETLabel Check Label StartingRobin D1B40T92040 Crankcase Assy LOCTITE221 50ML Silicon 30MLCover Sheet Blind RIVET3.2Robin D1B40T92040 Crankshaft Assy 01896200 5052970005306100 KEY Robin D1B40T92040 Camshaft Assy Flyweight Weight HAND-STCamlever Locking WasherRobin D1B40T92040 Piston Assy Circlip Gudgeon PINPiston Ring SET Conrod ScrewRobin D1B40T92040 cylinder head Assy Valve Guide Stud CYL.HEADPushrod Valve InletRobin D1B40T92040 Oil pump and gov. Assy Centrifugal Weight Schleif Paste 80GCOVER, OIL Pump Retaining StrapRobin D1B40T92040 timing Assy Bolt F.GOV.HOUSING LOCTITE648 10MLHOCHTEMP.FETT 400G Closing PlugParts not available separately CUP Spring F.GOVERNORGrub Screw M6X35 Hexagon NUT M6Robin D1B40T92040 Blower Flywheel & alt. Assy Blower Ring Spring Washer A4Allen Screw M4X20 FlywheelRobin D1B40T92040 Injection Equipment Assy Sealing Cone NozzleRobin D1B40T92040 Injection EQUIP. ASSY. Connecting Nipple Joint WASH.F.INJECTControl Sleeve CON.SPR.WASHERRobin D1B40T92040 recoil starter Assy Housing F.R.START Rubber SleeveReturn Spring Allen Screw M6X10Robin D1B40T92040 air ducting a Assy Loctite IS407 20G Spring ClipSealing STRIP119MM FILL.HEAD Screw M4X10Robin D1B40T92040 air ducting b Assy TECHNICOLL8058 0.75KG Sealing Strip 655MMSealing Strip 54MM Disc A6.4Robin D1B40T92040 Crankcase Breathing Sys. Assy Filter Breathing System Fuel Pipe LWSuction Pipe ClampRobin D1B40T92040 fuel tank Assy CAP F. Fuel Tank RopeFuel Hose Fuel VENT. ValveRobin D1B40T92040 fuel tank Assy Vent Valve Fuel FILT. EXT. MountAllen Screw M4X16 Lead Seal 8 MMRobin D1B40T92040 air filter Assy Includes Items W/ # Rubber Shell 32MMAIR Filter Element Knurled NUT M6Robin D1B40T92040 exhaust slicencer Assy Gasket Muffler Allen Screw M8X25HEX Screw M8X50 Pipe ClipRobin D1B40T92040 starter/REGULATOR Assy Plug Sleeve Housing Allen Screw M6X70Retaining Bracket STARTER12V 1.0KWRobin D1B40T92040 electric Equipment wiring Assy OIL Pressure Switch Electric WIRE/350MMElectric WIRE/430MM PIN TERM.HOUS.6WAYRobin D1B40T92040 speed control Assy Adjusting Screw Hexagon NUT M5Cable Clamp 2.2MM HEX Screw MTerms and Conditions of Sale Parts FReighT pOLiCYPage HERE’S HOW to GET Help

MVH406DSCPAS, MVH406DSZ specifications

The Multiquip MVH406DSZ and MVH406DSCPAS are powerful and robust vibratory plate compactors designed for various construction and civil engineering applications. These machines are engineered to provide exceptional performance, durability, and ease of use, making them suitable for both professional contractors and DIY enthusiasts.

The MVH406DSZ model features a reliable air-cooled, four-stroke gasoline engine, delivering optimal power and efficiency. With a weight of approximately 400 pounds, it offers excellent stability while compacting soil and asphalt materials. The machine operates at a frequency of around 5,600 vibrations per minute (VPM), ensuring rapid and effective compaction across various surfaces. The heavy-duty base plate measures 24 inches in width, providing optimal coverage for large areas and enhancing productivity on the job site.

One of the standout features of the MVH406DSZ is its innovative anti-vibration technology, designed to minimize operator fatigue during extended use. This feature allows for a more comfortable operating experience, as the vibration levels are significantly reduced, enabling operators to work longer without discomfort. Moreover, the ergonomic handle is adjustable and designed for ease of maneuverability, ensuring that operators can guide the compactor effortlessly around obstacles.

On the other hand, the MVH406DSCPAS model features similar core specifications but comes equipped with additional benefits, such as the compactor’s ability to use multiple attachments for various tasks. This versatility is a key characteristic that makes the MVH406DSCPAS model particularly advantageous for contractors looking to maximize their equipment's utility on diverse jobs.

Both models are designed with durability in mind, featuring high-quality materials that can withstand the rigors of frequent use. The plates are constructed from heavy-duty steel, ensuring longevity and resistance to wear and tear. Additionally, the compactors’ easy-access maintenance points facilitate quick oil changes and routine upkeep, prolonging the equipment's life and ensuring reliable performance.

In conclusion, the Multiquip MVH406DSZ and MVH406DSCPAS compactors are exceptional choices for anyone in need of reliable and efficient compaction equipment. With their powerful engines, advanced vibration-reducing technology, and rugged design, these models are well-suited for effective operation in both small and large-scale projects. Whether you require a machine for grading, trenching, or asphalt work, the MVH406 series delivers performance and durability that you can count on.
Top Page Image Contents