Multiquip MVH406DSCPAS, MVH406DSZ manual Battery Charging, Battery Cable Connection Option

Page 27

maintenance

„„Check the battery regularly and make sure that each electrolyte level is to the bottom of the vent well (Figure 35). If necessary add only distilled water in a well-ventilated area.

Figure 35. Battery Electrolyte Levels

BATTERY CHARGING

„„DO NOT charge battery with the battery cables connected to the compactor. The diodes will be damage by the high voltage.

„„Batteries generate hydrogen gas which

can be highly explosive. DO NOT smoke or allow flames or sparks near the battery, especially during charging of the battery.

„„Charge the battery in a open air environment (plenty of ventilation).

„„Before charging , remove the cap from each cell of the battery.

„„Connect the positive (+) lead of the charger to the positive (+) terminal of the battery and the negative (-) lead of the charger to the negative (-) terminal of the battery. DO NOT reverse the polarity when charging. Reverse polarity will damage the charger rectifier or the battery.

„„Battery fluid will be lost through continuous charging and discharging.

„„Discontinue charging if the electrolyte temperature exceeds 117° F (45° C).

NOTICE

During summer much more battery fluid is lost than in winter. Before starting, check battery electrolyte levels and replenish with distilled water to the upper mark on the battery.

BATTERY CABLE CONNECTION (Option)

1.Take off the battery cover by removing the M6 nuts that secure the battery holder to the cover.

2.When removing battery cables, disconnect the ground side (normally negative) first (Figure 36).

3.When installing battery cable connect the ground side (normally negative) last.

+ TERMINAL

BATTERY COVER

- TERMINAL

BATTERY

Figure 36. Removing Battery Cover

mvh406dsz/dsCPAs pLATE COMPACTOR • operation and parts manual — rev. #7 (02/28/14) — page 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Series Model MVH406DSZ/ MVH406DSCPAS Diesel engine exhaust and some PROPOSITION 65 WarningPage MVH406DZ/DSCPAS Reversible Plate Compactor Table of ContentsChoose from three easy options Safety Messages Safety InformationGeneRaL saFeTY Before servicing equipment Engine saFeTYFueL saFeTY BaTTeRY saFeTY eLeCTRiC sTaRT OnLY„ Use well-insulated gloves when picking up the battery Emission Control Label TRanspORTing saFeTYEnviROnmenTaL saFeTY/deCOmmissiOning EmissiOns inFORmaTiOnFuji Heavy Industries MVH406DSZ/DSCPAS Reversible Plate Compactor Dimensions DimensionsGeneral nformation MVH406DSZ/DSCPAS Reversible Plate Compactor Components ComponentsRobin Diesel Basic engineChecking the Hydraulic Oil Level Using a 24 mm wrench, remove the hydraulic oil filler plugBefore Starting Checking Engine Oil LevelRemove the fuel cap located on top of fuel tank Checking the Air CleanerLoosen the wing nut , remove the air cleaner cover Checking The FuelElectric Start Option Adjusting Handle HeightOperation Releasing the HandlePlace the throttle lever in the Start position center Recoil StartPush up the handle upward until the handle locks in place Normal ShutdownEmergency Shutdown Stowing the HandleCompaction Sensor MVH406 Dscpas Only Normal Compaction Compaction LimitFunction to Detect Electric System Abnormality System Diagnostics to Detect Operational Abnormalities„„Check for leakage of fuel or oil MaintenanceInspection and Maintenance Service Tables Daily ServiceReplacing the V-belt Engine Oil ReplacementReinstalling the V-belt Air Filter Every 6 Months or 400 HoursPrevent dirt and dust from entering Vibrator Oil Level CheckDraining Vibrator Oil Draining Hydraulic OilBattery Maintenance Option Adding Hydraulic OilBleeder plug should only be loosened, but not removed Battery Cable Connection Option Battery ChargingTroubleshooting Trouble shooting compactor Troubleshooting engine Trouble shooting engineDipstick Explanation of Code in Remarks Column Suggested Spare Parts Nameplates and decals MVH-406Decal Shell Tellus OIL Decal OIL SAE 10W-30Decal Model Logo MVH-406 Decal CautionVibrating Plate Assy Packing 1/4 CU Vibrating PlateOIL Gauge Copper PackingBase and Engine Assy Belt Cover in L100 BaseEngine ASSY., 1B40 Bolt 10X30TVibrator Assy GEAR, Drive Vibrating CaseRoller Bearing NJ310EMC4 Rotary SHAFT, DriveControl Handle Assy Rubber Coupling Handle BracketHandle Bracketr WASHER, Flat M12Control Handle Assy COVER, Throttle Lever Bolt 8X25 TThrottle Lever BAR GRIP, I.D MMHand Pump Assy Bush AccumlatorIncludes Items W/# Control ShaftBattery Assy Battery 46B24L Battery Cord 400LBattery Cord + 550L CRADLE, BatteryCOMPACTION Analyzing System ASSY. mVH4O6DSCPAS Wire CLIP, Sensor Wire HARNESS, SensorWire Harness COVER,BATTERYElectric Device Assy Wire Complete Buzzer EBLIgnition KEY Robin D1B40T92040 Spare Parts KIT Assy Gasket SET CRK.CASE 1000H MAINTE.KITEmergency KIT Robin D1B40T92040 Accessories Assy Label Starting Accessories KITTool SET Label CheckRobin D1B40T92040 Crankcase Assy Blind RIVET3.2 LOCTITE221 50MLSilicon 30ML Cover SheetRobin D1B40T92040 Crankshaft Assy 50529700 0189620005306100 KEY Robin D1B40T92040 Camshaft Assy Locking Washer FlyweightWeight HAND-ST CamleverRobin D1B40T92040 Piston Assy Conrod Screw CirclipGudgeon PIN Piston Ring SETRobin D1B40T92040 cylinder head Assy Valve Inlet Valve GuideStud CYL.HEAD PushrodRobin D1B40T92040 Oil pump and gov. Assy Retaining Strap Centrifugal WeightSchleif Paste 80G COVER, OIL PumpRobin D1B40T92040 timing Assy Closing Plug Bolt F.GOV.HOUSINGLOCTITE648 10ML HOCHTEMP.FETT 400GParts not available separately Hexagon NUT M6 CUPSpring F.GOVERNOR Grub Screw M6X35Robin D1B40T92040 Blower Flywheel & alt. Assy Flywheel Blower RingSpring Washer A4 Allen Screw M4X20Robin D1B40T92040 Injection Equipment Assy Nozzle Sealing ConeRobin D1B40T92040 Injection EQUIP. ASSY. CON.SPR.WASHER Connecting NippleJoint WASH.F.INJECT Control SleeveRobin D1B40T92040 recoil starter Assy Allen Screw M6X10 Housing F.R.STARTRubber Sleeve Return SpringRobin D1B40T92040 air ducting a Assy FILL.HEAD Screw M4X10 Loctite IS407 20GSpring Clip Sealing STRIP119MMRobin D1B40T92040 air ducting b Assy Disc A6.4 TECHNICOLL8058 0.75KGSealing Strip 655MM Sealing Strip 54MMRobin D1B40T92040 Crankcase Breathing Sys. Assy Clamp Filter Breathing SystemFuel Pipe LW Suction PipeRobin D1B40T92040 fuel tank Assy Fuel VENT. Valve CAP F. Fuel TankRope Fuel HoseRobin D1B40T92040 fuel tank Assy Lead Seal 8 MM Vent ValveFuel FILT. EXT. Mount Allen Screw M4X16Robin D1B40T92040 air filter Assy Knurled NUT M6 Includes Items W/ #Rubber Shell 32MM AIR Filter ElementRobin D1B40T92040 exhaust slicencer Assy Pipe Clip Gasket MufflerAllen Screw M8X25 HEX Screw M8X50Robin D1B40T92040 starter/REGULATOR Assy STARTER12V 1.0KW Plug Sleeve HousingAllen Screw M6X70 Retaining BracketRobin D1B40T92040 electric Equipment wiring Assy PIN TERM.HOUS.6WAY OIL Pressure SwitchElectric WIRE/350MM Electric WIRE/430MMRobin D1B40T92040 speed control Assy HEX Screw M Adjusting ScrewHexagon NUT M5 Cable Clamp 2.2MMFReighT pOLiCY Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help

MVH406DSCPAS, MVH406DSZ specifications

The Multiquip MVH406DSZ and MVH406DSCPAS are powerful and robust vibratory plate compactors designed for various construction and civil engineering applications. These machines are engineered to provide exceptional performance, durability, and ease of use, making them suitable for both professional contractors and DIY enthusiasts.

The MVH406DSZ model features a reliable air-cooled, four-stroke gasoline engine, delivering optimal power and efficiency. With a weight of approximately 400 pounds, it offers excellent stability while compacting soil and asphalt materials. The machine operates at a frequency of around 5,600 vibrations per minute (VPM), ensuring rapid and effective compaction across various surfaces. The heavy-duty base plate measures 24 inches in width, providing optimal coverage for large areas and enhancing productivity on the job site.

One of the standout features of the MVH406DSZ is its innovative anti-vibration technology, designed to minimize operator fatigue during extended use. This feature allows for a more comfortable operating experience, as the vibration levels are significantly reduced, enabling operators to work longer without discomfort. Moreover, the ergonomic handle is adjustable and designed for ease of maneuverability, ensuring that operators can guide the compactor effortlessly around obstacles.

On the other hand, the MVH406DSCPAS model features similar core specifications but comes equipped with additional benefits, such as the compactor’s ability to use multiple attachments for various tasks. This versatility is a key characteristic that makes the MVH406DSCPAS model particularly advantageous for contractors looking to maximize their equipment's utility on diverse jobs.

Both models are designed with durability in mind, featuring high-quality materials that can withstand the rigors of frequent use. The plates are constructed from heavy-duty steel, ensuring longevity and resistance to wear and tear. Additionally, the compactors’ easy-access maintenance points facilitate quick oil changes and routine upkeep, prolonging the equipment's life and ensuring reliable performance.

In conclusion, the Multiquip MVH406DSZ and MVH406DSCPAS compactors are exceptional choices for anyone in need of reliable and efficient compaction equipment. With their powerful engines, advanced vibration-reducing technology, and rugged design, these models are well-suited for effective operation in both small and large-scale projects. Whether you require a machine for grading, trenching, or asphalt work, the MVH406 series delivers performance and durability that you can count on.
Top Page Image Contents