Multiquip MVH406DSZ, MVH406DSCPAS Engine Oil Replacement, Air Filter Every 6 Months or 400 Hours

Page 24

maintenance

Engine Oil Replacement:

1.Replace engine oil, in first 25 hours of operation and every 50 to 100 hours afterwards.

2.Oil may be drained more easily when it is warm afteroperation (For more details, see separate engine Owner's Manual).

Air Filter (Every 6 Months or 400 Hours)

1.The air filter element (Figure 27) should be cleaned because a clogged air cleaner can cause poor engine starting, lack of power and shorten engine life substantially.

AIR

WING

ELEMENT

CLEANER

NUT

Figure 27. Engine Air Filter and Element

2.To clean or replace air filter loosen the wing nut on the air filter housing (Figure 27) remove the cover and take out air filter cartridge. If only cleaning of the air filter is desired blow through the air filter cartridge from the inside, moving a jet of dry compressed air up and down until all dust is removed.

CAUTION

NEVER attempt to check the V-belt with the engine running. Severe injury can occur if your hand gets caught between the V-belt and the clutch (Figure 28). Always use safety gloves.

CLUTCH

PULLEY

VIBRATOR

PULLEY

Figure 28. V-Belt Hazard

CLUTCH

V-BELT

VIBRATOR

PULLEY

Figure 29. V-Belt Check

Replacing the V-belt

„„Remove the belt cover (Figure 29). Engage an offset wrench 3/4”(19 mm) or the like to vibrator pulley (lower) fastening bolt. Engage wastecloth or the like at midway of V-belt on the left side and whilepulling it back strongly, rotate the offset wrench clockwise so that the V-belt will come off.

Reinstalling the V-belt

„„Engage V-belt to lower vibrator pulley and push the V-belt to leftside of upper clutch and, in the same manner as in removal, rotate offset wrench clockwise so that the V-belt goes back on.

Checking Clutch

„„Check the clutch simultaneously with V-belt checking. With belt cover removed, check outer drum of the clutch for seizure and "V" groove for wear or damage with your eyes. Clean the "V" groove as necessary. If the shoe is worn, power transmission becomes deficient and slipping will result.

Replacing Clutch

„„Remove V-belt. Remove bolt at engine power output by giving a light tap with a hammer to an engaged wrench and rotate bolt counterclockwise. Remove clutch with a pulley extractor. To reinstall, reverse the procedure.

CAUTION

When ever the compactor's vibration becomes weak or lost during normal operation regardless of operation hours, check the V-belt and clutch immediately.

page 24 — mvh406dsz/dsCPAs pLATE COMPACTOR • operation and parts manual — rev. #7 (02/28/14)

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Series Model MVH406DSZ/ MVH406DSCPAS PROPOSITION 65 Warning Diesel engine exhaust and somePage Table of Contents MVH406DZ/DSCPAS Reversible Plate CompactorChoose from three easy options Safety Information Safety MessagesGeneRaL saFeTY Engine saFeTY Before servicing equipmentFueL saFeTY BaTTeRY saFeTY eLeCTRiC sTaRT OnLY„ Use well-insulated gloves when picking up the battery TRanspORTing saFeTY EnviROnmenTaL saFeTY/deCOmmissiOningEmissiOns inFORmaTiOn Emission Control LabelFuji Heavy Industries Dimensions MVH406DSZ/DSCPAS Reversible Plate Compactor DimensionsGeneral nformation Components MVH406DSZ/DSCPAS Reversible Plate Compactor ComponentsBasic engine Robin DieselUsing a 24 mm wrench, remove the hydraulic oil filler plug Before StartingChecking Engine Oil Level Checking the Hydraulic Oil LevelChecking the Air Cleaner Loosen the wing nut , remove the air cleaner coverChecking The Fuel Remove the fuel cap located on top of fuel tankAdjusting Handle Height OperationReleasing the Handle Electric Start OptionRecoil Start Place the throttle lever in the Start position centerNormal Shutdown Emergency ShutdownStowing the Handle Push up the handle upward until the handle locks in placeNormal Compaction Compaction Limit Compaction Sensor MVH406 Dscpas OnlySystem Diagnostics to Detect Operational Abnormalities Function to Detect Electric System AbnormalityMaintenance Inspection and Maintenance Service TablesDaily Service „„Check for leakage of fuel or oilEngine Oil Replacement Reinstalling the V-beltAir Filter Every 6 Months or 400 Hours Replacing the V-beltVibrator Oil Level Check Draining Vibrator OilDraining Hydraulic Oil Prevent dirt and dust from enteringBattery Maintenance Option Adding Hydraulic OilBleeder plug should only be loosened, but not removed Battery Charging Battery Cable Connection OptionTroubleshooting Trouble shooting compactor Trouble shooting engine Troubleshooting engineDipstick Explanation of Code in Remarks Column Suggested Spare Parts MVH-406 Nameplates and decalsDecal OIL SAE 10W-30 Decal Model Logo MVH-406Decal Caution Decal Shell Tellus OILVibrating Plate Assy Vibrating Plate OIL GaugeCopper Packing Packing 1/4 CUBase and Engine Assy Base Engine ASSY., 1B40Bolt 10X30T Belt Cover in L100Vibrator Assy Vibrating Case Roller Bearing NJ310EMC4Rotary SHAFT, Drive GEAR, DriveControl Handle Assy Handle Bracket Handle BracketrWASHER, Flat M12 Rubber CouplingControl Handle Assy Bolt 8X25 T Throttle LeverBAR GRIP, I.D MM COVER, Throttle LeverHand Pump Assy Accumlator Includes Items W/#Control Shaft BushBattery Assy Battery Cord 400L Battery Cord + 550LCRADLE, Battery Battery 46B24LCOMPACTION Analyzing System ASSY. mVH4O6DSCPAS Wire HARNESS, Sensor Wire HarnessCOVER,BATTERY Wire CLIP, SensorElectric Device Assy Wire Complete Buzzer EBLIgnition KEY Robin D1B40T92040 Spare Parts KIT Assy Gasket SET CRK.CASE 1000H MAINTE.KITEmergency KIT Robin D1B40T92040 Accessories Assy Accessories KIT Tool SETLabel Check Label StartingRobin D1B40T92040 Crankcase Assy LOCTITE221 50ML Silicon 30MLCover Sheet Blind RIVET3.2Robin D1B40T92040 Crankshaft Assy 50529700 0189620005306100 KEY Robin D1B40T92040 Camshaft Assy Flyweight Weight HAND-STCamlever Locking WasherRobin D1B40T92040 Piston Assy Circlip Gudgeon PINPiston Ring SET Conrod ScrewRobin D1B40T92040 cylinder head Assy Valve Guide Stud CYL.HEADPushrod Valve InletRobin D1B40T92040 Oil pump and gov. Assy Centrifugal Weight Schleif Paste 80GCOVER, OIL Pump Retaining StrapRobin D1B40T92040 timing Assy Bolt F.GOV.HOUSING LOCTITE648 10MLHOCHTEMP.FETT 400G Closing PlugParts not available separately CUP Spring F.GOVERNORGrub Screw M6X35 Hexagon NUT M6Robin D1B40T92040 Blower Flywheel & alt. Assy Blower Ring Spring Washer A4Allen Screw M4X20 FlywheelRobin D1B40T92040 Injection Equipment Assy Sealing Cone NozzleRobin D1B40T92040 Injection EQUIP. ASSY. Connecting Nipple Joint WASH.F.INJECTControl Sleeve CON.SPR.WASHERRobin D1B40T92040 recoil starter Assy Housing F.R.START Rubber SleeveReturn Spring Allen Screw M6X10Robin D1B40T92040 air ducting a Assy Loctite IS407 20G Spring ClipSealing STRIP119MM FILL.HEAD Screw M4X10Robin D1B40T92040 air ducting b Assy TECHNICOLL8058 0.75KG Sealing Strip 655MMSealing Strip 54MM Disc A6.4Robin D1B40T92040 Crankcase Breathing Sys. Assy Filter Breathing System Fuel Pipe LWSuction Pipe ClampRobin D1B40T92040 fuel tank Assy CAP F. Fuel Tank RopeFuel Hose Fuel VENT. ValveRobin D1B40T92040 fuel tank Assy Vent Valve Fuel FILT. EXT. MountAllen Screw M4X16 Lead Seal 8 MMRobin D1B40T92040 air filter Assy Includes Items W/ # Rubber Shell 32MMAIR Filter Element Knurled NUT M6Robin D1B40T92040 exhaust slicencer Assy Gasket Muffler Allen Screw M8X25HEX Screw M8X50 Pipe ClipRobin D1B40T92040 starter/REGULATOR Assy Plug Sleeve Housing Allen Screw M6X70Retaining Bracket STARTER12V 1.0KWRobin D1B40T92040 electric Equipment wiring Assy OIL Pressure Switch Electric WIRE/350MMElectric WIRE/430MM PIN TERM.HOUS.6WAYRobin D1B40T92040 speed control Assy Adjusting Screw Hexagon NUT M5Cable Clamp 2.2MM HEX Screw MTerms and Conditions of Sale Parts FReighT pOLiCYPage HERE’S HOW to GET Help

MVH406DSCPAS, MVH406DSZ specifications

The Multiquip MVH406DSZ and MVH406DSCPAS are powerful and robust vibratory plate compactors designed for various construction and civil engineering applications. These machines are engineered to provide exceptional performance, durability, and ease of use, making them suitable for both professional contractors and DIY enthusiasts.

The MVH406DSZ model features a reliable air-cooled, four-stroke gasoline engine, delivering optimal power and efficiency. With a weight of approximately 400 pounds, it offers excellent stability while compacting soil and asphalt materials. The machine operates at a frequency of around 5,600 vibrations per minute (VPM), ensuring rapid and effective compaction across various surfaces. The heavy-duty base plate measures 24 inches in width, providing optimal coverage for large areas and enhancing productivity on the job site.

One of the standout features of the MVH406DSZ is its innovative anti-vibration technology, designed to minimize operator fatigue during extended use. This feature allows for a more comfortable operating experience, as the vibration levels are significantly reduced, enabling operators to work longer without discomfort. Moreover, the ergonomic handle is adjustable and designed for ease of maneuverability, ensuring that operators can guide the compactor effortlessly around obstacles.

On the other hand, the MVH406DSCPAS model features similar core specifications but comes equipped with additional benefits, such as the compactor’s ability to use multiple attachments for various tasks. This versatility is a key characteristic that makes the MVH406DSCPAS model particularly advantageous for contractors looking to maximize their equipment's utility on diverse jobs.

Both models are designed with durability in mind, featuring high-quality materials that can withstand the rigors of frequent use. The plates are constructed from heavy-duty steel, ensuring longevity and resistance to wear and tear. Additionally, the compactors’ easy-access maintenance points facilitate quick oil changes and routine upkeep, prolonging the equipment's life and ensuring reliable performance.

In conclusion, the Multiquip MVH406DSZ and MVH406DSCPAS compactors are exceptional choices for anyone in need of reliable and efficient compaction equipment. With their powerful engines, advanced vibration-reducing technology, and rugged design, these models are well-suited for effective operation in both small and large-scale projects. Whether you require a machine for grading, trenching, or asphalt work, the MVH406 series delivers performance and durability that you can count on.
Top Page Image Contents