Fuse Replacement, Lamp Replacement, Specifications

FUSE REPLACEMENT

The power cord is fuse-protected against short-circuiting, by a 10-amp fuse located in the tip of the DC power plug. If the DC socket is powered, but the unit does not operate, then the cooler/warmer fuse may be open.

To inspect or replace the DC Power Cord Fuse

1.Unscrew the end-cap of the DC plug counterclockwise.

2.Remove fuse, inspect it for an open element, and replace with a new 10 amp fuse, if needed.

3.Re-attach the end-cap to the plug.

4.If new fuse opens, call Vector Customer Service Department for further instructions and possible return/replacement. This unit is not user-serviceable, it must be returned to Vector Manufacturing for professional service or repair. Any attempt to service by user will void warranty.

LAMP REPLACEMENT

At the inside top of the cooler there is a lamp that lights when the cooler door is opened. If the lamp does not light when the door is opened, and the unit is powered, the cartridge type bulb should be replaced. These are available from most automotive supply stores. Replace the bulb with one that is the same type and rating.

1.Disconnect all power to the cooler/warmer

2.Empty the cooler of it’s contents

3.Turn the cooler upside down so that the lamp assembly is down and is accessible.

4.Slide the clear plastic cover part way towards the front of the unit.

5.Lift the clear cover and expose the bulb

6.Using a paperclip, form a half-inch hook at one end.

7.Hook the paperclip under the bulb at one end and lift the end of the bulb.

8.The bulb will disconnect from the springs of the socket.

9.Place the new bulb between the socket springs.

10.Replace the clear plastic cover by reversing the removal actions.

11.Turn the unit right side up.

12.Apply power and open the door.

If there are any problems call Vector Technical Support Toll Free (866) 584-5504.

SPECIFICATIONS

Capacity . . . . . . . . . . . . . . . . . . . . . . . 21 twelve oz. cans /16 Liter/4.2 Gallons (US) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Volt DC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 7', with fused 12 Volt DC power plug Replaceable fuse in DC Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Amps Replaceable Interior Lamp . . . . . . . . . . . . . . . . . . . . . 12V, 3.6 watt cartridge (Festoon) AC/DC Power Adapter . . . . . . . . . . . . . . . . . . 110 Volt AC to 12 Volt DC at 4 Amps. Amperage Draw . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 Amperes (approx. 45-watts) Cooling Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cools to average 40 °F

Warming Performance . . . . . . . . . . . . . . . . . . . . . . Warms to 60 °F above surrounding air or 120 degrees maximum

Cold/Heat Transfer . . . . . . . . . . . . . . . . . . . . . . .Temperature-efficient, easy clean liner Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CFC-free liner Heat Dissipation . . . . . . . . . . . . . . . . . . . . . . Built-in fan with long-life, brushless motor Warm/Cool System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Non-wearing thermoelectric Outside Dimensions . . . . H 19in. (48.3cm) x W 11.5 in. (29.3cm) x D 11.25 in. (28.6cm) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.65lbs (6.19 Kg)