U-Line CO2175FF, C2275DWR, 2175RF manual Checking Drawer Alignment, Adjusting Drawer Alignment

Page 21

11 Standard Drawers

Checking Drawer Alignment

The unit’s drawers are aligned at the factory before shipment. However, their alignment could have been disturbed during shipment or during overlay panel installation. Check each drawer to confirm that it is aligned:

Aligned

Front-to-Back

Aligned

Side-to-Side

Aligned

Top-to-Bottom

•Side-to-Side— When viewed from the top, the drawer front should be square with the sides of the cabinet.

•Front-to-Back— When viewed from the side, the drawer front should be straight with the cabinet’s sides, not cocked forward or back.

•Top-to-Bottom— When viewed from the front, the drawer should be level horizontally.

Adjusting Drawer Alignment

WARNING

SHOCK HAZARD — The unit must be unplugged from the wall outlet during drawer removal, adjustment and re-installation.

Drawer Removal

1. Confirm that the unit is

Mounting

unplugged from wall outlet.

Screw

 

2. Unplug the drawer’s connection wiring (top drawer only).

3. Remove the mounting screws.

4.Pull the drawer completely out of the unit.

CAUTION

Use care when handling the drawer. Drawer edges, drawer rail and the unit’s slide may be sharp.

IMPORTANT

Drawer adjustments are made by moving the slide that carries the drawer’s rail. Minor adjustments may be made by loosening one of the slide’s mounting screws, adjusting the slide and retightening the screw. Severe adjustments may be made by removing the slides’ mounting screws, drilling new mounting holes and remounting the slide.

Side-to-Side Adjustment

The drawer will need a Side-to-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side Adjustment if, when viewed

 

 

 

 

 

from the top, the drawer front is

 

 

 

 

 

not square with the sides of the

 

 

 

 

 

cabinet. This is caused by one of

 

 

 

 

 

the slides being mounted too far

 

 

Not Aligned Side-to-Side

forward on the unit’s liner.

 

 

 

 

 

 

 

 

 

 

Minor Adjustment:

 

 

Top View of Unit

 

 

 

Note: The mounting holes on the

slide are slightly larger than theLoosen Mounting Screws

screws’ diameter.

1. Loosen the slide’s mounting screws.

2. Push the slide backward.

3. Retighten the screws.

Push Slide

 

Backward

Severe Adjustment:

Note: The slides have extra

mounting holes that may be used. Mark and Drill New Mounting Holes

1.Remove the slide’s mounting screws.

2.

Reposition the slide so it is the

 

 

same distance from the front

 

 

of the liner as the other slide.

 

 

Measure to confirm.

Push Slide

 

 

3.

Mark new drilling holes using

Backward

 

different sets of mounting holes on the slide.

Note: Front location holes are shown. Corresponding rear holes will also need to be marked.

4.Drill all the new holes with a #30 drill bit.

5.Remount the slide.

Not Aligned Front-to-Back

Front-to-Back Adjustment

The drawer will need a Front-to- Back Adjustment if, when viewed from the side, the drawer front is cocked forward or back. This is caused by the front slide mountings not being level with the rear slide mountings.

Side View of Unit

U-Line Drawer Alignment

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents USE and Care Guide Please Record Your Model Information Read and save this Use and Care GuideTable of Contents Line Use and Care Guide General Precautions Safety Alert DefinitionsCombo Model Features Ice Makers FeatureContemporary grille design. Integrates seemlessly into Air Flow Adjusting Air TemperatureInitial Startup Electronic Control PanelChecking Product Temperature To check the actual product temperature in the unitInterior Lighting Touch Electronic Control Quick GuideTo turn the unit on or off Control DialAdjusting Air Temperature Other Models DrawersTop Storage Bin CrisperIce Maker Operation Ice Maker AdjustmentLeveling Removing and Installing Interior ShelvesRemoving and Installing Grille Removing and Installing Door ShelvesInstalling the grille Line Use and Care Guide To align and adjust the door Door Alignment and AdjustmentDoor Reversability Reversing the doorReinstall hinge to top opposite Reinstall hinge to bottom oppositeReinstall Hole Plugs Prepare door for reinstallationTo reverse the door Remove grille Remove top hinge, and doorRemove bottom hinge Prepare door for reinstallation For black or white doors Install bottom hingeInstall top hinge, and door Install grilleChecking Drawer Alignment Adjusting Drawer AlignmentTop-to-Bottom and Left-to-Right Adjustment Re-installation of DrawerExterior Cleaning Interior CleaningDefrosting Storage, Vacation and Moving Condensor CleaningProduct Disposal Interval Every Six MonthsIf Service is Required Before Calling for ServiceReplacement Parts Troubleshooting GuideLine Use and Care Guide Line Corporation Limited Warranty LINE.COM
Related manuals
Manual 180 pages 38.87 Kb Manual 24 pages 53.32 Kb Manual 24 pages 15.99 Kb

C2275DWR, 2175RF, CO2175FF specifications

The U-Line CO2175FF and 2175RF are two of the standout offerings in U-Line’s expansive portfolio of beverage centers, designed to provide both functionality and elegance in residential and commercial settings. Known for their commitment to quality and innovation, U-Line has crafted these models to meet the diverse needs of modern consumers.

The CO2175FF features a dual zone temperature management system, allowing users to store wine and beverages at optimal temperatures. With a precise range from 34°F to 60°F, it ensures that your collections will be preserved perfectly, making it ideal for wine enthusiasts and casual drinkers alike. The refrigerator is equipped with a stainless steel exterior, which not only provides a sleek and sophisticated look but also ensures durability. The glass door is UV-resistant, protecting your beverages from harmful light exposure.

On the other hand, the U-Line 2175RF model focuses on a robust refrigeration system designed for maximum storage capacity. This model features adjustable shelving that provides flexibility to accommodate bottles of various sizes, from standard wine bottles to larger formats. With a total capacity of approximately 24 wine bottles, it gives ample space for your collection while maintaining easy access to all your favorites.

Both models boast a quiet operation and are designed to be energy-efficient, making them ideal for those looking to minimize their environmental impact without sacrificing performance. With state-of-the-art technology such as the touch control panel, users can easily adjust settings and monitor temperature conditions, ensuring peace of mind when it comes to beverage storage.

The U-Line CO2175FF and 2175RF also feature built-in LED lighting, which not only enhances visibility but also adds a touch of ambiance to any room. Users can enjoy their favorite drinks in style, thanks to the elegant interior design.

In summary, the U-Line CO2175FF and 2175RF models represent the perfect blend of style and functionality. With features like dual temperature zones, adjustable shelving, and energy-efficient technology, they cater to the needs of modern beverage storage, making them an excellent choice for any home or business. Whether entertaining guests or simply enjoying a quiet evening, these beverage centers offer a sophisticated solution for all your storage needs.
Top Page Image Contents