U-Line CO2075FF manual Installation Instructions, Removing Existing Door

Page 9

CO2075FF — Ice Maker/Refrigerator

 

13/32"

 

 

0.177" Dia. (#16 Drill)

 

 

 

 

 

13/32"

 

 

 

 

 

 

 

x

11/16" Deep

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3/8"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3/8"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13/16"

 

 

 

 

Door Bottom:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5/16" Dia. x 1/4" Deep

 

 

 

 

 

 

 

 

 

Chamfer 1/32" x 45°

 

 

 

 

 

Top View

 

Bottom View

4.Drill hole for upper door hinge (top of panel) (see Figure 16, Top View).

0.177" diameter

(#16 drill) x 11/16" deep

5.Drill hole for lower door hinge (see Figure 16, Bottom View).

5/16" diameter x 1/4" deep

CAUTION

1/8"

13/16"

1-17/32"

7/16"

5/16" Dia.

x 1/2" Deep

13/32"

1/8"

 

1/8"

 

 

 

 

 

 

1/32" R

1/8" R

13/16"

3/4"

It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed.

Installation Instructions

Removing Existing Door

1.

Remove the door shelves by first pulling shelves

 

up at a 45° angle then straight out (see Figure 37

 

on Page 15).

2.

Remove top hinge screw pin (7/64" hex key or Phillips

 

screwdriver, depending on your unit’s construction).

 

Remove the door by tilting forward and lifting off the

Back View

Side View

Figure 16

Route notch in top corner of overlay panel as shown (see Top and Side Views). Top of notch is entire depth of panel, front to back.

bottom hinge pin.

3. Pull door gasket out of the groove (top edge of door

only). Start in the middle and pull outward, moving

toward the edge (see Figure 17). This may take some

force.

Width: 13/16"

Depth: 1/8"

Route notch in backside of top corner of overlay panel (see Back and Side Views).

Width: 13/16"

Depth: 1/8"

Height: 1-17/32" from top edge of panel (less 1/8" for depth of notch on top of panel)

Radius of corner notch: 1/8" (see Back View)

3.Drill holes for pivot plate mounts (see Figure 16, Back View).

5/16" diameter x 1/2" deep, from the routed surface

Figure 17

New Handle

Old Handle

Figure 18

CAUTION

Be careful not to drill too deep! Drilling holes too deep may destroy your door panel.

4.Remove the three screws located on the back of the handle (see Figure 18).

02/2005

9

www.U-LineService.com

Image 9
Contents CO2075FF Ice Maker/Refrigerator Follow Safety Precautions ContentsInspect and Plan General PrecautionsTools/Materials Required InspectionCut-Out Dimensions Exterior CleaningPrepare Site Black and White ModelsDoor Swing/Clearances Information Reversing the Door Product DimensionsOther Site Requirements Power SupplyWater Supply Environmental RequirementsPrepare and Install Door Panel Side-By-Side Installation InstructionsDoor Panel Installation Custom 1/4 Door Panel InsertFull Overlay Door Panel Removing Existing Door Installation InstructionsAttaching the Full Overlay Panel Assembling the Door Installing the DoorAdjust Door Adjusting Door AlignmentChecking Door Alignment To 6 Prepare PlumbingGo on to 7 Prepare Power Supply Water Supply ConnectionPrepare Plumbing Installation Tip Electrical SpecificationsPrepare Power Supply Level the Unit Install the UnitInstallation Troubleshooting Installation of the CO2075FFInstall the Unit Relocating the ShelvesAbout Settings Start-Up TroubleshootingInitial Start-Up Start-Up for the First TimeWho to Call Service Information

CO2075FF specifications

The U-Line CO2075FF is an elegantly designed, all-refrigerator unit that caters to those who appreciate both aesthetics and functional efficiency in their kitchen appliances. This compact model boasts a sleek finish that seamlessly blends with any modern kitchen decor, making it not only a practical addition but also a stylish one.

One of the main features of the U-Line CO2075FF is its remarkable storage capacity relative to its size. With a spacious interior that can accommodate up to 75 cans, the refrigerator is engineered to maximize utility in confined spaces. This makes it an ideal choice for apartments, smaller homes, or even as a supplementary refrigerator in larger kitchens.

The U-Line CO2075FF is equipped with innovative technologies that enhance its functionality. The unit features a state-of-the-art convection cooling system that ensures rapid temperature recovery and consistent temperature distribution throughout the refrigerator. This technology is essential for preserving the freshness of food and beverages, particularly in environments where the refrigerator door is frequently opened.

In terms of temperature control, the U-Line CO2075FF offers a user-friendly digital interface that allows for precise adjustments. Users can easily set the temperature to their desired level, ensuring that their items are stored under optimal conditions. The refrigerator also includes a powerful compressor that operates quietly, minimizing disruption in the home environment.

Another characteristic that sets the U-Line CO2075FF apart is its LED interior lighting. The energy-efficient lights not only illuminate the contents for easy visibility but also contribute to the overall energy efficiency of the unit. Moreover, this refrigerator comes with adjustable shelving, allowing users to customize the interior layout to accommodate items of various sizes, from tall bottles to small jars.

For those who prioritize energy savings, the U-Line CO2075FF is Energy Star certified, meaning it operates with reduced energy consumption without sacrificing performance. This commitment to sustainability makes it an attractive option for eco-conscious consumers.

In summary, the U-Line CO2075FF is a well-rounded refrigerator that combines style, efficiency, and advanced technologies. Its thoughtful design, superior cooling capabilities, and user-friendly features make it a standout choice for anyone looking to enhance their kitchen with a reliable and aesthetically pleasing refrigeration solution.