Taylor 342, 340, 341 manual Section Safety, To Operate Safely

Page 7

Section 3

Safety

 

 

We at Taylor are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the service technician. As an example, warning labels have been attached to the freezer to further point out safety precautions to the operator.

IMPORTANT -- Failure to adhere to the following safety precautions may result in severe personal injury. Failure to comply with these warnings may damage the machine and its components. Component damage will result in part replacement expense and service repair expense.

To Operate Safely:

DO NOT operate the freezer without reading this operator’s manual. Failure to follow this instruction may result in equipment damage, poor freezer performance, health hazards, or personal injury.

SDO NOT operate the freezer unless it is properly grounded.

SDO NOT attempt any repairs unless the main power supply to the freezer has been disconnected.

SDO NOT operate the freezer with larger fuses than specified on the freezer data label.

Failure to follow these instructions may result in electrocution or damage to the machine. Contact your local authorized Taylor Distributor for service.

DO NOT use a water jet to clean or rinse the freezer. Failure to follow this instruction may result in serious electrical shock.

SDO NOT allow untrained personnel to operate this machine.

SDO NOT operate the freezer unless all service panels and access doors are restrained with screws.

SDO NOT remove the door, beater, scraper blades, drive shaft, or torque rotor shaft unless all control switches are in the OFF position.

SDO NOT put objects or fingers in the door spout.

Failure to follow these instructions may result in contaminated product or severe personal injury to fingers or hands from hazardous moving parts.

USE EXTREME CAUTION when removing the beater assembly. The scraper blades are very sharp and may cause injury.

These freezers must be placed on a level surface. Failure to comply may result in personal injury or equipment damage.

DO NOT obstruct air intake and discharge openings:

Models 341/342: 3” (76 mm) minimum air space on all sides.

Model 340: 6” (152 mm) minimum air space on sides and 0” at the rear. It is recommended to install a skirt to one side of the unit, and to place the back of the unit against a wall.

Failure to follow this instruction may cause poor freezer performance and damage to the machine.

These freezers are designed to operate indoors, under normal ambient temperatures of 70_--75_F (21_--24_C). The freezers have successfully performed in high ambient temperatures of 104_F (40_C) at reduced capacities.

NOISE LEVEL: Airborne noise emission does not exceed 78 dB(A) when measured at a distance of 1.0 meter from the surface of the machine and at a height of 1.6 meters from the floor.

061211

Models 340, 341, 342

3

Safety

 

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Slush Freezers Information found on the data label Table of Contents Models 340, 341 Table of Contents Electrical Connections SectionWater Connections Water Cooled Units Only Air Cooled UnitsTo the Operator Compressor Warranty DisclaimerTo Operate Safely Section SafetyModel Operator Parts Identification511 Model Models 340, 341, 342 Beater Door Assembly KAY-5 AccessoriesSection Important To the Operator Assembly Section Operating ProceduresModels 340, 341 Operating Procedures Operating Procedures Models 340, 341 Step Sanitizing Step Optional Rack AssemblyPriming Step Optional Flavor Rack Assembly Closing ProcedureRinsing Draining Product From Freezing CylinderCleaning Brush Cleaning DisassemblyRegular Maintenance Checks Important Operator ChecklistDuring Cleaning and Sanitizing Troubleshooting Bacterial CountWinter Storage Problem Probable Cause Remedy Section Troubleshooting GuideModels 340, 341 Troubleshooting Guide Problem Probable Cause Remedy Part Description Every Annually QTY Months Parts Replacement ScheduleWarr Remarks Parts Number QTY Class Update Section Parts ListModels 340, 341 Parts List Hood Panel A.--SIDE Lower Spring EXTENSION.375X.025X2.25 Water Cooled Models 340/341 Rev /06 Model 341 049359--33 Rev /06 Model 340/341 049359--40 Rev /06 Model 341 049359--58 Rev /06 Model 342 052720--27 Rev /06 Model 342 052720--33 Rev /06 Model 342 052720--40 Rev /06 Model 342 052720--58 Rev /06

341, 342, 340 specifications

The Taylor 340, 341, and 342 series are distinguished models within the acclaimed Taylor guitar lineup, celebrated for their craftsmanship, tonal richness, and versatility. Each model in this series offers unique features that appeal to musicians of various genres, making them a popular choice among performers and hobbyists alike.

The Taylor 340 model, known for its exceptional sound, is characterized by its combination of Sapele back and sides with a solid Sitka spruce top. This pairing results in a balanced tone that suits both fingerstyle players and strummers. The 340 is designed with an elegant body shape, providing comfortable playability while delivering pronounced midrange frequencies, which makes it an excellent choice for those wanting a guitar that can cut through the mix in a band setting.

Moving on to the Taylor 341, this model enhances the features of the 340 with the addition of a tropical mahogany back and sides, lending warmth and depth to its overall sonic profile. The solid Sitka spruce top remains a staple, ensuring that the guitar retains clarity and articulation. The 341's body size strikes a balance between comfort and projection, making it an ideal option for both intimate performances and larger venues. Players often appreciate the 341 for its dynamic range, allowing for expressive playing styles from intricate fingerpicking to robust strumming.

Finally, the Taylor 342 rounds out the series with its unique appointments and tonal characteristics. Like the other models, it features a solid Sitka spruce top, but pairs it with ovangkol back and sides. This combination gives the 342 a brilliant, bright tone with notable sustain and articulation. The design also includes sleek aesthetics, with an eye-catching rosette and binding that enhances its visual appeal. The guitar is equipped with Taylor’s renowned Expression System® electronics, providing exceptional amplified sound for live performances.

Overall, the Taylor 340, 341, and 342 models share a commitment to quality, innovation, and tonal excellence. Each model's design reflects Taylor's philosophy of marrying modern technology with traditional craftsmanship, resulting in instruments that not only sound great but are also a joy to play. Musicians can choose from this series based on their personal tone preferences and performance needs, ensuring that every player finds a perfect fit within the Taylor family.
Top Page Image Contents