Smeg LVF649B instruction manual User instructions, Cleaning The Filter Unit, Prolonged Disuse

Page 30
CLEANING THE FILTER UNIT

User instructions

CLEANING THE FILTER UNIT

It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip the tabs, turn them anticlockwise and lift upwards;

push the centre filter D from the underside to remove it from the micro-filter:

separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows;

remove the centre filter by lifting it upwards.

GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE:

The filters should be cleaned under running water using a stiff brush.

When removing the filter, take care that there are no food residues on it. If any residues fall into the washing pit they might block hydraulic components, or foul the spray arm nozzles.

It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged.

Carefully replace the filters in their seats, to avoid damaging the wash pump.

PROLONGED DISUSE:

Run the soak program twice in succession.

Unplug the power cord from the socket.

Leave the door slightly open, in order to prevent the formation of unpleasant odours inside the washing tank.

Fill the rinse aid dispenser.

Shut off the water supply tap.

29

Image 30
Contents Page Contents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVEDSafety instructions THIS DISHWASHER MUST BE USED BY ADULTSSafety instructions AQUASTOP MODELSAPPLIANCE Installation instructions 2. Installation and hook-upFor free-standingmodels only DRAIN CONNECTION Installation instructionsCONNECTING TO THE WATER SUPPLY 2.1 Water supply connectionInstallation instructions 2.2 Electrical connection and precautionsL = brown N = blue = yellow-green Installation instructions Fuse replacementFOR GREAT BRITAIN ONLY 3.1 Front panel User instructions3. Description of the controls 1 ON/OFF BUTTON 2 START/PAUSE BUTTONSETTING THE WASHING PROGRAM User instructions3.2 Washing programs SWITCHING ONUser instructions Before starting a washing program make sure thatINTERRUPTION A PROGRAM User instructionsEND OF PROGRAM CHANGING A PROGRAMpresente solamente su alcuni modelli User instructionsDELAYING THE PROGRAM disponibile in tutti i programmi escluso lammolloUser instructions TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES 4. Operating instructions 4.1Using the water softening systemUser instructions ADJUSTING THE WATER SOFTENING SYSTEM User instructions4.2 Using the rinse aid and detergent dispensers User instructionsWATER HARDNESS TABLE ADJUSTING THE RINSE AID DISPENSER SETTING User instructionsADDING THE RINSE AID User instructions ADDING THE DETERGENTUser instructions The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-freebut contain natural enzymesUser instructions 4.3 General warnings and recommendationsUser instructions Items which are not dishwasher-safeLOWER BASKET 4.4 Using the basketsUser instructions LOADING THE LOWER BASKETUPPER BASKET User instructionsCUTLERY BASKET insertUser instructions LOADING THE UPPER BASKETLoading examples Models with cutlery racks ADJUSTING THE UPPER BASKET User instructionsVersion B User instructions CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER User instructionsPROLONGED DISUSE CLEANING THE FILTER UNITUser instructions Fill the rinse aid dispenserTROUBLESHOOTING MINOR PROBLEMS User instructionsIf the program fails to start, check that User instructions there is rinse aid inside the special containerSafety level 6. TroubleshootingFAULT User instructionsE7 E8 E9 FAULTUser instructions DESCRIPTIONUser instructions TECHNICAL DATAWater supply pressure Electrical characteristics WidthMontare la porta e regolarelatensione delle mollelaterali primadell’installazionedes ressortslateraux avant l’installation einstellen