Smeg LSA14X7 instruction manual User instructions, End Of Cycle, Removing The Dishes

Page 17

END OF CYCLE

User instructions

If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. You must wait about 1 minute before closing the door to restart the program. When the door is closed the program will continue from where it was interrupted. This operation should only be carried out if strictly necessary, because it might cause problems in execution of the program.

END OF CYCLE

At the end of the washing cycle the dishwasher gives a short acustic signal and the program indicators nr 4 and 5 start blinking (the word "end" is displayed on the window).

To switch off the dishwasher, open the door and press the ON/OFF button (1).

REMOVING THE DISHES

At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket.

16

Image 17

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. Safety and operating instructions Safety instructionsUSES OTHER THAN THOSE DESCRIBED ABOVE NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELS2.1 Water supply connection Installation instructions2. Installation and hook-up DRAIN CONNECTION CONNECTING TO THE WATER SUPPLYIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD 2.2 Electrical connection and precautionsNEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD FOR GREAT BRITAIN ONLY Fuse replacement3. Description of the controls User instructionsSELECTED PROGRAM INDICATOR LIGHTS 3.1 Upper panel“3/1” OPTION BUTTON 13 INFORMATION DISPLAY SETTING THE WASHING PROGRAM AND SWITCHING ON“3/1” OPTION LIGHT HALF LOAD BUTTONReference program as per EN 50242 standard See energy label 0,85 0,03100’ 1,20Before starting a washing program make sure that 3.2 Washing programsThe correct amount of detergent has been added to the dispenser EXTRA PROGRAMSDELAYED START available in all programs except the soak program SELECTING HALF LOAD WASHavailable in all programs except the soak program CHANGING THE PROGRAM CANCELLING THE CURRENT PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES END OF CYCLE4.1 Using the water softening system 4. Operating instructionsADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENTUser instructions MAKE SURE that the items being washed are dishwasher-safe 4.3 General warnings and recommendationsCorrect loading of the dishes helps ensure optimal washing results Dishes and objects in copper, tin, zinc or brass these tend to stain Items which are not dishwasher-safeLOWER BASKET 4.4 Using the basketsLoading examples ½ LOAD LOADING THE LOWER BASKETCUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKETDepending on the models, the basket may be equipped with some or all of the following accessories Version B ADJUSTING THE UPPER BASKETUser instructions CLEANING THE WATER INTAKE FILTER 5. Cleaning and maintenanceCLEANING THE SPRAY ARMS 5.1 General warnings and recommendationsGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE CLEANING THE FILTER UNITPROLONGED DISUSE Fill the rinse aid dispenser Shut off the water supply tapIf the dishes are not being cleaned properly, check that TROUBLESHOOTING MINOR PROBLEMSBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE Reconnect the water intake hose and open the tap againIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that FAULT 6. TroubleshootingSafety level E1 E2 E3 E4 E5 E6Turbine flow-regulator malfunction E7 E8 E9Alternate washing system malfunction Water intake system malfunctionElectrical characteristics TECHNICAL DATAWidth Height depending on models Capacity Water supply pressure