Andrew ES76PK-1 installation instructions Step

Page 19

Step 2

Step 3

Once all 16 Short Struts are installed and securely fastened, re-install Rear Enclosure Panel. Carefully rotate the enclosure right-side-up as shown in Figure 12. Place tempo- rary wood blocks under each of the enclosure’s three support pads with the additional block positioned in between.

Install Ribs (222673) to enclosure strut as shown in Figure 12. Attach Target Screws supplied from Alignment Kit (223711) as shown and tighten. Leave all other hardware loose.

Eccentric Bolt, 300084A

1/2” Washer, 9997-101 Section B-B

1/2-13 Lock Nut, 9979-54

(Truss, Short Strut, 300077)

Hole #27

1/2”x1/2” Shoulder Bolt 3/8” Nut, 9999-60 Lockwasher, 9974-63 3/8” Washer, 9997-89 1/2” Washer, 9997-101

(300081)

View C-C

1/2-13x1.0, Shoulder Bolt, 9858-18

1/2” Washer, 9997-101

1/4” Spacer, 209765-1

3/8” Lockwasher, 9974-63

3/8-16 Nut, 9999-60

3/8” Washer, 9997-79

(Inner Strut, 300080)

Rib, 222673

Install Target Screws

Hole #20

Truss, Short Strut, 300077

Truss Plate, 300081

1/2”x1.0 Shoulder Bolt, 9858-18

1/2” Washer, 9997-101

1/4” Spacer, 209765-1

3/8” Washer, 9997-89

3/8” Lockwasher, 9974-63

3/8” Nut. 9999-60

5/8”x2.0 Bolt & Nut, 45980-1

Washer, 9997-227

Section A-A

Inner Strut, 300080

(300080)

1/2”x1/2 Shoulder Bolt, 9858-19

1/2” Washer, 9997-101

1/4” Spacer, 209765-1

3/8” Washer, 9997-89

View D-D3/8” Lockwasher, 9974-63 3/8” Nut. 9999-60

Figure 12

21

Installation Procedures

Image 19
Contents Meter ESA Table of Contents Introduction Meter Earth Station AntennaProprietary Data Information and Assistance Technical Customer Service CenterHow to Use This Manual Overview ContentGetting Started OverviewTool Size Quantity Recommended ToolsGetting Started Returning Equipment Step Overview Foundation Preparation Installation Procedures1b A-325 Tensioning For bolts over four diameters Tensioning StepPedestal Ground Mount Assembly Installation Step Step Step Azimuth Jack Arm Installation Azimuth Jackscrew Assembly Step AZ Jack Pin 302383 4 Washer, 9997-188 8x1.0 Bolt Lockwasher Elevation Jackscrew Assembly Step Reflector Backstructure Assembly Step Step Step Step Typical 4 Places Then panel 3 and panel 4, and so on Step Theodolite Reflector AlignmentRib Panel Skin Refer to Figure Step Installation Procedures Installation Procedures Step Reflector Alignment Installation Procedures Installation Procedures Reflector to Ground Mount Assembly Step View A-A Subreflector Installation StepSubreflector Strut Support 300089 4 Places Adjustment Hardware, 3 Places Part Subreflector Centering Step Focusing Operation Overview Acquiring a SatelliteStep Polarization at 45 degrees from Optimum Setting Maximizing Odd Transponders Subreflector Adjustment Survival Struts Preventive Maintenance Overview General Cleaning Electrical PartsPreventive Maintenance Antenna Preventive Maintenance Drive System Voltage Current Checks Step Step Preventive Maintenance Jackscrews/Motors Gear Motor/Housing Fill Drain Requirements Lubrication Chart Preventive Maintenance

ES76PK-1 specifications

The Andrew ES76PK-1 is a robust and highly efficient satellite communication antenna designed for both commercial and military applications. Its innovative design and advanced features make it an exceptional choice for high-performance connectivity.

One of the standout characteristics of the ES76PK-1 is its impressive gain. With a gain of approximately 76 dBi across a wide range of frequencies, it ensures optimal signal reception and transmission even in challenging environments. This high gain makes it ideal for applications requiring reliable long-distance communication, such as remote site operations or disaster recovery efforts.

The construction of the ES76PK-1 also prioritizes durability and resilience. Built with sturdy materials, this antenna is resistant to harsh weather conditions, including high winds, rain, and extreme temperatures. Its lightweight yet robust design allows for easier installation and maintenance, making it suitable for both fixed and mobile setups.

In terms of technology, the Andrew ES76PK-1 leverages advanced polarization techniques, which enhance its ability to transmit and receive signals effectively. This polarization capability ensures minimal signal degradation and interference, providing users with consistent and high-quality communication links. Furthermore, the antenna supports multiple frequency bands, thus offering flexibility in deployment and compatibility with various satellite systems.

The antenna's design incorporates a high level of precision engineering. This not only contributes to its excellent performance but also allows for fine azimuth and elevation adjustments. This feature is crucial in aligning the antenna accurately with satellite signals, further improving the quality of service for users.

Another key aspect of the Andrew ES76PK-1 is its compatibility with a range of RF systems. This versatility makes it a favored choice among service providers and enterprises looking to implement or upgrade their satellite communication infrastructure.

In summary, the Andrew ES76PK-1 stands out in the competitive landscape of satellite communication technologies. With its high gain, durable construction, advanced polarization, and compatibility with various systems, it meets the stringent demands of modern communication needs. This antenna is an excellent investment for anyone looking to achieve reliable and efficient satellite connectivity.