Sub-Zero PRO VENTILATION HOODS G N At U R E P O L I S H, Cleaning a N D Care, Heat L a M P S

S I G N AT U R E P O L I S H

Signature Polish is available from Signature Limited Laboratory,

P. O. Box 13436, Dayton, Ohio 45413-0436, or call 877-376-5474 (toll free).

W O L F PRO VENTILATION HOOD U S E & C A R E

H A L O G E N L I G H T I N G		CLEANING A N D CARE
All Wolf Pro ventilation hoods and hood liners		Most surfaces of your Wolf Pro hood are
have halogen lighting with two settings.		stainless steel. Although resistant to most
Halogen bulbs are included with the hood.		stains, it is not totally impervious to damage.
	Pro wall hoods, 30" (762), 36" (914) and 42"
	(1067) wide require two 50W, 120V par 20	G E N E R A L C L E A N I N G
	halogen bulbs. 48" (1219), 54" (1372), 60"		Salt and some cooking liquids may pit and
	(1524) and 66" (1676) wide hoods require
			stain the surface. Always remove any film
	three 50W, 120V par 20 halogen bulbs.
			or spills immediately.
	Pro island hoods, 36" (914) and 42" (1067)
			Avoid using abrasive cleaners. They will
	wide require two 50W, 120V par 20 halogen
			permanently scratch the surface.
	bulbs. 54" (1372) and 66" (1676) wide hoods
	require three 50W, 120V par 20 halogen		Do not use steel wool pads.
	bulbs.		Be careful not to soak the rotary switches.
	Pro hood liners, 28" (711), 34" (864), 40"
			Although they are sealed, excessive
	(1016) and 46" (1168) wide require two 50W,		moisture may cause damage to the
	120V par 20 halogen bulbs. 52" (1321) and		controls.
	58" (1473) wide hood liners require three		Use a clean cloth or sponge, wipe with
	50W, 120V par 20 halogen bulbs.
			warm water and mild detergent. Rinse and
To replace halogen bulbs, turn off the ventila-			dry immediately. Apply protective polish,
tion hood blower and lights. Once the halogen			always in the same direction as the grain.
bulb is cool, use a soft cloth to unscrew the			A spray degreaser will remove fingerprints
bulb and replace.
			and greasy spatters. Spray on a cloth and
			wipe surface. Buff dry immediately to avoid
			streaking.
	Be sure that the bulb is cool before		Apply a protective polish to the surface to
	replacing. Halogen bulbs get hot instantly
			maintain luster and protect against food
	and adjacent parts may retain heat.
			stains.
			Use white vinegar and water to remove
			hard water stains.

HEAT L A M P S

Wolf Pro 27" (686) deep wall hoods are equipped with two heat lamp locations that require R40, 250W maximum bulbs. Heat lamp bulbs are not included with the hood.

To replace, turn off the ventilation hood blower and lights. Once the heat lamp bulb is cool, use a soft cloth to unscrew the bulb and replace.

Be sure that the heat lamp bulb is cool before touching.

D E C O R AT I V E R A I L

Clean the decorative hood rail using warm soapy water. Then hand dry with a clean, soft cloth.

It is not necessary to remove the decorative rail from the hood assembly. It should be cleaned in place.

Be careful not to pull or hang on the bar, as this could damage the hood assembly.

12

Dimensions in parentheses are in millimeters unless otherwise specified.