Sub-Zero 3 1 5 I P manual To R a G E B I N L E V E L a D J U S T M E N T

Page 19

S U B - Z E RO MODELS 315I A N D 315IP O P E R AT I O N

1)Open the door and remove the control box cover.

2)Locate the cube size adjustment screw shown in the illustration below. To make fuller cubes, turn the screw clockwise about 1/4 turn. This will make the freezing cycle longer.

3)To shorten the freezing cycle and make cubes that are not as full, turn the adjust- ment screw 1/4 turn counterclockwise.

4)After the next freezing cycle, the cubes should have responded to the adjustment; if another adjustment is required, do it early in the freeze cycle.

S TO R A G E B I N L E V E L A D J U S T M E N T

When the ice maker shuts off, the ice level in the storage bin should be even with the metal tube inside the bin. If the ice in the storage bin is too high or too low, turn the ice maker control knob to adjust the ice storage bin thermostat. Refer to the illustration below.

To lower the ice level, turn the knob counter- clockwise. To increase the ice level, turn the knob clockwise. Usually a 1/8 turn will be enough for either adjustment.

H A RV E S T T I M E A D J U S T M E N T

The amount of harvest time may be adjusted. It is preset from the factory at about three minutes, which should be adequate to release all cubes and fill the reservoir. If the timer needs to be adjusted, follow these steps:

1)Unplug the ice maker or disconnect the electrical power.

2)Remove the kickplate/grille.

3)Remove the control box cover.

4)Locate the timer shown in the illustration below. Loosen the set screw that holds the two halves of the timer cam together.

5)Rotate one half of the cam to open or close the lower portion of the cam. More of an opening equals more harvest time and less of an opening means less harvest time.

6)Tighten the set-screw.

7)Replace the control box cover and kickplate/ grille.

8)Reconnect the electrical power.

Electrical Shock Hazard—Disconnect electrical power before beginning removal of parts.

Control Knob

Ice maker control knob

Cube Size Adjustment

Cube size adjustment

Harvest time adjustment

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Installation & Operation N T E N T S N TA C T F O R M AT I O N Thank YOUWAT E R S U P P LY R S U P P LYWAT E R Q U a L I T Y E R a L L D I M E N S I O N S E a R E Q U I R E M E N T SD E L S 3 1 5 I a N D 3 1 5 I P P O RTA N T N OT E B Z E RO Models 315I a N D 315IP I N S TA L L AT I O NModel S TA L L AT I O N S P E C I F I C AT I O N SDrain pump #12250321 T I O N a L M P O N E N T SA I N P U M P K I T Drain pump kit #A36892020C U R E T H E I C E M a K E R InstallationC K P L AT E / G R I L L E I N S TA L L AT I O N V E L I N GV E R S E T H E D O O R S W I N G D E PA N E L SS TA L L AT I O N PA N E L S I G N O R PA N E L I N S TA L L AT I O NN G E C O V E R I N S TA L L AT I O N E G R E E D O O R S to PN TA C T F O R M AT I O N B Z E RO Models 315I a N D 315IP F E AT U R E S WA R R a N T YD E L 3 1 5 N T I M E I T I a L S TA RT- U P E C U B E SE S to R a G E B I N I N G YO U R I C E M a K E RE E Z E C Y C L E W T H E I C E M a K E R U S E S WAT E RRV E S T C Y C L E G N AT U R E P O L I S H CleaningB Z E RO Models 315I a N D 315IP O P E R AT I O N E a N I N G T H E I C E S to R a G E B I NImportant Note do not use automotive E M a K E R AdjustmentsE a N I N G T H E I C E M a K I N G S Y S T E M N T E R I Z I N GRV E S T T I M E a D J U S T M E N T To R a G E B I N L E V E L a D J U S T M E N TTroubleshooting G U I D E But no ice falling Unit operatesStorage bin RO D U C T R E G I S T R AT I O N RV I C E I N F O R M AT I O N N TA C TRV I C E I N F O R M AT I O N F O R E C a L L I N G F O R S E RV I C EM I T E D W a R R a N T Y Full TWO Year Warranty0 0
Top Page Image Contents