True Manufacturing Company GDIM-26, GDIM-49 Electrical Instructions, Sealing Cabinet to Floor

Page 11

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

ELECTRICAL INSTRUCTIONS

Step 5

A.Before your new unit is connected to a power supply, check the incoming voltage with a voltmeter. If anything less than 100% of the rated voltage for operation is noted, correct immediately.

B.All units are equipped with a 7 ft. (2.1m) service cord, and must be powered at proper operating voltage at all times. Refer to cabinet data plate for this voltage.

True requires that a sole use circuit be dedicated for the unit. Failure to do so voids warranty.

WARNING

Compressor warranties are void if compressor burns out due to low voltage.

WARNING

Power supply cord ground should not be removed!

NOTE

To reference wiring diagram - Remove front louvered grill, wiring diagram is positioned on the inside cabinet wall.

SEALING CABINET TO FLOOR

Step 1 - Position Cabinet

Allow three inches between the wall and rear of the GDM freezer for proper ventilation.

Step 2 - Level Cabinet

Cabinet should be level, side to side and front to back. Place a carpenter’s level in the interior floor in four places:

A. Position level in the inside floor of the unit near the doors. (Level should be parallel to cabinet front). Leve cabinet.

B. Position level at the inside rear of cabinet. (Again level should be placed parallel to cabinet back).

C. Perform similar procedures to steps a & b by placing the level on inside floor (left and right sides - parallel to the depth of the cooler). Level cabinet.

Step 3

Draw an outline on the base on the floor.

Step 4

Raise and block the front side of the cabinet.

Step 5

Step 6

Raise and block the rear of the cabinet

Step 7

Apply sealant on floor as outline in Step 5. on other three sides.

Step 8

Examine to see that cabinet is sealed to floor around entire perimeter.

Note:

Asphalt floors are very susceptible to chemical attack. A layer of tape on the floor prior to applying the sealant will protect the floor.

NSF Approved Sealants:

1.Minnesota Mining #EC800 Caulk

2.Minnesota Mining #EC2185 Caulk

3.Minnesota Mining #EC1055 Bead

4.Minnesota Mining #EC1202 Bead

5.Armstrong Cork - Rubber Caulk

6.Products Research Co. #5000 Rubber Caulk

7.G.E. Silicone Sealer

8.Dow Corning Silicone Sealer

Apply a bead of “NSF Approved Sealant”, (see list below),To floor on half inch inside the outline drawn. The bead must be heavy enough to seal the entire cabinet surface when it is down on the sealant.

9

www.truemfg.com

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Table of Contents True Food Service Equipment, Inc Safety Precautions Safety Information Refrigerant Disposal Proper Disposal of the RefrigeratorUSE of Extension Cords Before You Throw Away Your Old Refrigerator or FreezerHOW to Connect Electricity Uncrating Installation / Operation Instructions OwnershipRequired Tools Unit leveling Installation of Legs and CastorsLocating Securing Castors and LegsLeveling Warranty is void if ventilation is insufficientConductors and Circuits Level Cabinet Electrical InstructionsSealing Cabinet to Floor Position CabinetRecommendation Replacement PartsLight Switch Location StartupFreezers Defrost Time Clock Operation Grasslin TimerOverload Protector If the Compressor will Not RUNStarts but Trips Repeatedly onCoil Defrost Heater CabinetTemperature ControlDefrostTime Clock Defrost Control OnThe Evaporator Drain PanRequired Tools MAINTENANCE, Care & Cleaning Cleaning the Condenser CoilRemove the louvered grill Disconnect the electrical power to the unitStainless Steel Equipment Care and Cleaning IDL Integrated Door Lighting Light Bulb ReplacementTrue Food Service Equipment, Inc

GDIM-26, GDIM-26NT, GDIM-49 specifications

True Manufacturing Company is renowned for its commitment to producing high-quality refrigeration equipment, catering to a variety of sectors, including food service and beverage industries. Among its diverse product lineup, the True GDIM-49, GDIM-26NT, and GDIM-26 models stand out for their innovative features, advanced technologies, and exceptional performance.

The True GDIM-49 is designed for high-volume businesses, offering an impressive amount of storage space with a capacity of 49 cubic feet. This unit is equipped with energy-efficient, heavy-duty compressors that maintain optimal temperatures, ensuring food safety and freshness. The exterior is constructed from durable stainless steel, providing significant resistance to corrosion and wear, while the interior includes a bright LED lighting system that enhances visibility and improves accessibility to stored items. Additionally, the GDIM-49 features a self-closing door design to prevent unnecessary energy loss.

In contrast, the True GDIM-26NT is tailored for establishments with moderate storage requirements. This model maintains a 26 cubic foot capacity while still embodying the same high standards of quality as its larger counterpart. The GDIM-26NT incorporates advanced refrigeration technology and energy-efficient components, guaranteeing consistent temperature control. One of its standout characteristics is the use of a no-frost evaporator, eliminating the need for manual defrosting and ensuring ease of maintenance over time. The model also features adjustable shelving, allowing users to customize their storage solutions as needed.

Lastly, the True GDIM-26 is similar in size and functionality to the GDIM-26NT but comes without the no-frost feature. This model is perfect for establishments looking for dependable refrigeration without the additional technology, making it a more budget-friendly option. The durable construction and efficient cooling systems in both models guarantee that products remain at optimal temperatures, crucial for food safety.

In summary, True Manufacturing Company’s GDIM-49, GDIM-26NT, and GDIM-26 models represent a fusion of style, functionality, and innovative technology. Businesses can rely on these units for their performance and reliability, confirming True's reputation as a leader in commercial refrigeration. Each model is designed to meet the specific needs of different establishments while maintaining True's hallmark commitment to quality and durability.
Top Page Image Contents