AEG K 9 18 00-4 I Regulations, Standards, Guidelines, Installation Location

Page 7

Installation

Installation Location

The appliance should be set up in a well ventilated, dry room.

Energy use is affected by the ambient temperature. The appliance should therefore

not be exposed to direct sunlight;

not be installed next to radiators, cookers or other sources of heat;

only be installed at a location whose ambient temperature corresponds to the climate classification, for which the appliance is designed.

The climate classification can be found on the serial plate, which is located at the left on the inside of the appliance.

The following table shows which ambient temperature is correct for each climate classification: each climate classification:

Climate classification

 

for an ambient temperature of

 

 

 

 

 

 

SN

 

+10 bis +32 °C

 

 

 

N

 

+16 bis +32 °C

 

 

 

ST

 

+18 bis +38 °C

 

 

 

T

 

+18 bis +43 °C

 

 

 

If installation next to a source of heat is unavoidable, the following mini- mum clearances must be maintained at the sides of the appliance:

for electric cookers 3 cm;

for oil and coal fired ranges 30 cm.

If these clearances cannot be maintained a heat insulating pad is required between the cooker and the refrigeration appliance.

Changing the light bulb

Warning! There is a risk of electric shocks! Before changing the light bulb, switch off the appliance and unplug it, or pull the fuse or the circuit breaker.

Light bulb data: 220-240 V, max. 15 W

1.Unplug the mains plug.

2. To change the light bulb press on the rear hook and at the same time slide the cover in the direction indicated by the arrow.

3. Change the defective light bulb.

4.Refit the light bulb cover.

5.Put the refrigerator back into opera- tion.

Regulations, Standards, Guidelines

This appliance was designed for household use and was manufactured in accordance with the appropriate standards. The necessary measures in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and the regu- lations of the German Society of Electrical Engineers (VDE) were observed in the manufacture of this appliance.

The refrigerant circuit has been checked for leaks.

This appliance is in accordance with the following EU guidelines:

73/23/EWG dated 19 February 1973 - low voltage guidelines.

89/336/EWG dated 3 May 1989

Your appliance needs air

For safety reasons, minimum ventilationmust be as shown Fig.

Attention: keep ventilation ope- nings clear of obstruction;

50 mm

min.

200 cm2

 

min.

 

200 cm2

D567

 

(including guideline change notice 92/31/EWG) - EMV guideline

22

31

Image 7
Contents 10/04 Santo K 9 18 00-4Respect des règles d’hygiène InstallationDear customer Contents Avertissements importants SafetyCase of malfunction DisposalSommaire Daily OperationDisposal Remove transport safeguardChère Cliente, Cher Client Disposal of old AppliancesChanging the light bulb InstallationInstallation Location Regulations, Standards, GuidelinesRehingeing the door Housing dimensionsElectrical connection Prior to Initial Start-UpWhat to do if Operating and indicator panelTemperature setting buttons Energy Saving TipsAfter cleaning wipe with fresh water and rub dry Cleaning and CareTemperature display Starting Up Setting the TemperatureDefrosting Interior AccessoriesSwitching off the appliance Fresh food refrigeration

K 9 18 00-4 I specifications

The AEG K 9 18 00-4 I is a versatile and efficient power tool designed for professional tradespeople and DIY enthusiasts alike. This cordless impact wrench stands out for its robust construction and advanced features that cater to high-demand applications, making it an essential addition to any toolkit.

One of the most notable characteristics of the AEG K 9 18 00-4 I is its powerful motor. With a maximum torque of 180 Nm, this impact wrench is capable of tackling even the toughest fastening tasks. It delivers swift performance, allowing users to easily drive larger bolts and fasteners with minimal effort. Its high-speed impact mechanism ensures rapid rotation and impact, culminating in improved efficiency and reduced working time.

The tool is built around AEG's innovative 18V battery platform, which provides exceptional power and runtime. The AEG K 9 18 00-4 I is compatible with a range of lithium-ion batteries that offer increased longevity and reduced charging time. This feature is particularly beneficial for professionals who require reliable tools that can withstand the rigors of daily use.

Ergonomically designed, the impact wrench is lightweight and easy to handle, reducing user fatigue during prolonged operation. Its soft-grip handle provides a comfortable and secure grip, enhancing overall control. Additionally, the built-in LED work light illuminates dark workspaces, ensuring that users can see what they're doing, even in challenging environments.

Another significant technology featured in the AEG K 9 18 00-4 I is the variable speed trigger. This allows operators to adjust the speed and torque settings according to the specific requirements of the job at hand. This level of customization makes it suitable for a variety of applications, from automotive work to construction tasks.

The tool is designed for durability, featuring a robust housing that can withstand the rigors of frequent use. Its impact-resistant casing protects the internal components, promoting longevity. Furthermore, the integrated electronic protection system prevents overheating, prolonging the life of both the motor and battery.

In conclusion, the AEG K 9 18 00-4 I impact wrench combines power, efficiency, and user-friendly features into a compact package. Its innovative technologies, durable design, and compatibility with the AEG battery platform make it an ideal choice for those seeking a reliable and powerful cordless tool for fastening applications. Whether for professional or home use, this impact wrench is sure to meet and exceed expectations.