Cornelius R-134A Water Flush Syrup Systems, Purge Water OUT of Syrup Systems Restore Operation

Page 20

13.Syrup Tank Systems.

Connect sanitizing solution tank, pressurized at 60 to 80-psi, into one of the syrup systems. Bag-in-Box Syrup System.

Place all bag-in-box syrup containers syrup outlet tubes in container containing sanitizing solution.

14.Sanitize the syrup system and dispensing valve as follows:

A.Place waste container under applicable dispensing valve.

B.Activate the dispensing valve for one minute to purge all water from and install sanitizing solution in the syrup system and dispensing valve.

C.Continue to activate the dispensing valve in cycles (“ON”for 15-seconds, “OFF”, then “ON”for 15-seconds). Repeat “ON”and “OFF”cycles for 15-cycles.

15.Repeat steps13 and 14 to flush water out of and install sanitizing solution in the remaining syrup systems and dispensing valves.

16.Remove sanitizing solution source from the syrup system.

17.Allow sanitizing solution to remain in the syrup systems for not less than 10 or no more than 15-minutes (max.) contact time.

STEP 4. WATER FLUSH SYRUP SYSTEMS

WARNING: Flush sanitizing solution from the syrup systems as instructed. Residual sanitizing solution left in the syrup systems could create a health hazard.

18.Fill syrup tank (syrup tank system) or a five-gallon container (bag-in-box system) with potable water.

19.Syrup Tank Systems.

Connect syrup tank containing potable water, pressurized at 60 to 80-psi, into one of the syrup systems. Bag-in-Box Syrup System.

Place all bag-in-box syrup containers syrup outlet tubes in container containing potable water.

20.Flush sanitizing solution from the syrup system and the dispensing valve as follows:

A.Place waste container under applicable dispensing valve.

B.Activate the dispensing valve for one minute to purge all sanitizing solution out of the syrup system and the dispensing valve.

C.Continue to activate the dispensing valve in cycles (“ON”for 15-seconds, “OFF”, then “ON”for 15-seconds). Repeat “ON”and “OFF”cycles for 15-cycles.

21.Repeat steps 19 and 20 preceding to purge sanitizing solution out of the remaining syrup systems and dispensing valves.

22.Remove potable water source from the syrup system.

STEP 5. PURGE WATER OUT OF SYRUP SYSTEMS (RESTORE OPERATION)

23.Syrup Tank Systems.

A.Noting syrup tanks CO2 regulator pressure setting observed in step 4 preceding, readjust CO2 regula- tor to the observed pressure setting,

B.Connect tanks containing syrup into syrup systems.

17

312021002

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Sentry III-A POST-MIX Cooling Unit This Document Contains Important InformationTable of Contents Table of Contents cont’d Safety Information Recognize Safety InformationThis page Left Blank Intentionally Warranty Reference Information General InformationClaims Instructions Design DataDROP--IN Refrigeration Assembly Data DescriptionTheory of Operation Sentry III-A Cooling UnitSystem Flow Diagram Carbonator Water Pump Motor Safety Thermostat Parts Identification312021002 OWNER’S Recommended Maintenance Maintenance ScheduleThis page Left Blank Intentionally Daily PRE-OPERATION Check Operators InstructionsOperating Controls This page Left Blank Intentionally General Maintenance AdjustmentsContent Water Where a Local Water Problem Exist Sanitizing Syrup SystemsCleaning Condenser Coil Replenishing CO2 SupplyPeriodic Cleaning of Cooling Unit Cleaning and SanitizingReplenishing Syrup Supply Wash Syrup SystemsFlush Syrup Systems Sanitize Syrup SystemsPurge Water OUT of Syrup Systems Restore Operation Water Flush Syrup Systems312021002 Troubleshooting TOO LOW.CONT’D Compressor does notCompressor Operates Continuously but doesWarranty Page One Cornelius Place Anoka, Minnesota 612 800
Related manuals
Manual 54 pages 24.45 Kb

R-134A specifications

Cornelius R-134A is a refrigerant commonly used in various cooling and air conditioning applications. It belongs to the hydrofluorocarbon (HFC) family and has become a favored alternative to many ozone-depleting substances. Unlike its predecessors, R-12, which has been phased out due to its detrimental effects on the ozone layer, R-134A offers a more environmentally friendly solution, albeit still having global warming potential.

One of the main features of R-134A is its favorable thermodynamic properties. It exhibits a low boiling point of approximately -26.3°C (-15.3°F), making it suitable for various refrigeration applications, including automotive air conditioning, commercial cooling systems, and domestic refrigerators. Its efficiency is regarded as superior, allowing for quick heat absorption and dissipation. This efficiency translates into energy savings, ultimately benefiting both consumers and manufacturers.

R-134A also boasts a relatively high vaporization heat, demonstrating its effectiveness in heat transfer processes. The low toxicity and non-flammability of R-134A further enhance its appeal, as it poses minimal risk during handling and application. This characteristic makes R-134A safer for technicians and users compared to older refrigerants, which presented higher health hazards.

Within modern technologies, R-134A plays a crucial role in both chiller systems and heat pump applications. It is compatible with various lubricants, allowing manufacturers to utilize R-134A in existing systems with minimal modifications. However, it is essential to use the correct type of oil, as mixing different types can lead to system inefficiencies and potential failure.

Despite its advantages, R-134A has a global warming potential of around 1,430 times greater than carbon dioxide, prompting the refrigerant industry to look for alternatives. Newer refrigerants, such as R-1234yf, offer lower environmental impact, driving a shift towards more sustainable options.

In conclusion, Cornelius R-134A remains a widely used refrigerant known for its efficiency, safety, and effectiveness in heat transfer. While it has played a significant role in the refrigeration and air conditioning industries, the ongoing search for eco-friendly alternatives highlights the need for continued innovation and adherence to environmental standards.
Top Page Image Contents