Audiovox AV-428V manual Bs Equalizer EQ Button, Bu Liquid Crystal Display Panel, Cl Cassette Door

Page 8
STATION SCAN (SCN) BUTTON

OPERATING INSTRUCTIONS

8

pre-set memories on the band in use. After entering the stations into memory, the unit will automatically stop at each station for 5 seconds so each can be heard. If you have already set the pre-set memories to your favorite stations, activating the Auto-Store Tuning feature will erase those stations and enter the new ones. This feature is most useful when travelling in a new area where you are not familiar with the local stations.

br STATION PRE-SET MEMORIES

To set any of the 6 pre-set memories in each band, use the following procedure:

1. Turn the radio on and select the desired band.

2. Select the first station to be pre-set using the Automatic Up/Down bm, or Manual Seek bn Tuning Controls.

3. Press and hold the pre-set button to be set for approximately 2 seconds. The pre-set number will appear on the display panel indicating that the station is now set into that pre-set memory position. The station can now be recalled at any time by pressing that button.

4. Repeat the above procedure for the remaining 5 pre-sets on that band and for the other 3 bands on the unit.

bs EQUALIZER (EQ) BUTTON

The EQ button applies preset sound effects to the unit’s audio output signal.The EQ button, when pressed, will activate one of the following operating modes ( CLASSICS, POP M, ROCK M, DSP OFF or FLAT). If the Equalizer function is active, as momentarily displayed on the panel, and the bass and/or treble level is set, the Equalizer function reverts to the the FLAT setting. On the other hand, if the Equalizer function is activated, the bass/treble setting(s) are ignored. Conversely, when the Equalizer function is not active, the unit returns to the user set bass

and treble levels.

bt

When this button is pressed during radio operation, each station in the current band will be scanned in the upward direction; each displayed station will flash for 5 seconds before moving on to the next station. If the local mode is active, only the stronger, nearby stations in the current band will be scanned. When the desired station appears, press the SCN button again to remain on that frequency.

bu LIQUID CRYSTAL DISPLAY PANEL

The Liquid Crystal Display (LCD) panel displays the frequency, time and activated functions, including a combination audio level/disc indicator in the form of dual

disc icons ( ) with circular bar graphs depicting the

strength of the audio signal. In addition, the display also contains a receive signal indicator which depicts the relative strength of the incoming broadcast frequency.

NOTE: It is a characteristic of LCD panels that, if subjected to cold temperatures for an extended period of time, they may take longer to illuminate than under normal conditions. In addition, the visibility of the numbers on the LCD may slightly decrease. The LCD read-out will return to normal when the temperature increases to a normal range.

cl CASSETTE DOOR

Hold the cassette with the exposed tape edge to the right and insert it fully into the cassette door until the cassette is engaged and begins playing (TAPE will appear on the display panel, together with three tape direction arrows). When the cassette reaches the end on the side of the tape being played, the unit will automatically change direction of play as shown by reversal of the three tape direction arrow indications on the display panel.

NOTE: Observe cassette operation cautions in Care and Maintenance section of this manual.

cm& cnFAST-FORWARD/REWIND BUTTONS

( / ) These buttons cause the tape to move rapidly in the direction indicated by the arrows. For example, if the button is pushed when the tape is moving from left to right ( >>> on the display panel), the tape will fast-

forward. If the button is pressed while the tape is moving from right to left ( <<< on the display panel), the tape will rewind. To stop fast tape movement, lightly push the opposite button. If the tape is allowed to fast-forward or rewind all the way to the end, the tape will reverse and automatically resume play.

co PROGRAM SELECTOR

To manually reverse tape direction and play the other side (program) of the cassette, lightly push both the Fast-

Forward and Rewind buttons ( and ) at the same time. The change of direction will be shown by the arrows on the display panel.

cp EJECT BUTTON ( )

Tape playback is stopped and the cassette is ejected by pressing this button. Radio operation will automatically resume when the cassette is ejected.

NOTE: Never leave a cassette engaged in the player when not in use. Doing so can cause damage to the cassette and/or mechanism of the unit. Always press the eject button and remove the cassette before removing the detachable front panel.

cq MODE SELECTOR (MODE)

During radio or tape play, press this button to select operation of the optional CD changer as shown by CDC, the disc number and the track number on the display panel. Refer to the CD Changer Controls section for specific operating instructions.

128-6634

8 of 16

Image 8
Contents AV-428 Installation Instructions Installation InstructionsUnsnap AT 2 Places InstallationInstructions Wiring Radio WiringSpeaker Wiring Speaker WiringOperating Instructions Operating InstructionsBn Manual Seek Tuning Bl AM/FM Band Selector BandBo LOCAL/DISTANT Selector LOC Bp FM Mono Selector MonoCq Mode Selector Mode Bs Equalizer EQ ButtonBu Liquid Crystal Display Panel Cl Cassette DoorCt Reset Button Cr TIME/FREQUENCY Selector T/FCsTHEFT-DETERRENT LED Cu Front Panel Release ButtonCare and Maintenance Care and MaintenanceSpecifications / Notes on Discs SpecificationsThis page Left Blank Intentionally CD Changer Controls CD Changer ControlsCD Changer Error Codes CD Changer Error CodesWarranty Month Limited WarrantyAudiovox Electronics Corp., Hauppauge, NY