Cornelius Non-Carbonated Post-Mix Beverage Dispenser operation manual Counter-top Installation

Page 7

Non-Carbonated Impulse Installation & Operations Manual

INSTALLATION PROCEDURE

Counter-top Installation

NOTE: Optional 4-inch legs (p/n 3184) will elevate the unit 4 inches above counter (order 4 legs).

1.Place the unit on a level counter capable of supporting at least 400 pounds.

2.Remove drip tray and front access panel.

3.Turn power switch off then remove screw located next to the power switch and the screw at top of front panel. Next, remove front panel, disconnect wires to valve key lock switch, and peal back magnetic decals from the top. Lift off top center section.

4.Pull water, concentrate, and CO2 lines through counter or wall. To comply with NSF International requirements the unit must be sealed to the counter top and all access holes in the unit base must be sealed, or the unit can be installed using the optional 4-inch legs (P/N 3184). Caulk/seal the unit to the counter using Dow Corning RTV 731 or equivalent approved sealant.

5.Pull plastic “wire tie” to remove hitch pin from condenser fan motor assembly (this pin is only needed during shipping).

Hitch Pin

Wire Tie

6.Fill the water bath with clean water until it comes out the overflow tube. Make sure the overflow tube is not blocked or plugged. Use low-mineral tap water, not distilled or deionized water.

Fill water bath through hole in top

NOTE: Water bath must be filled with water before the unit will run.

GLOBAL ICE BANK CONTROL (GIBO) THEORY OF OPERATION

Once electrical power is supplied to the Unit, the agitator motor will start. There will be a three-minute time delay before the refrigeration compressor and the con- denser fan motor will start. This three- minute time delay will take place each time electrical power to the Unit is interrupted.

The Unit will continue to operate until ice covers all three stainless-steel pins on the ice bank control probe. The ice bank control module senses this by measuring the differ- ence in electrical resistance between the water and the ice. When the ice on the

evaporator coil becomes thick enough, it covers the three stainless-steel pins on the ice bank control probe. The control module senses there is enough ice and turns the refrigeration compressor and the con- denser fan motor off.

The Unit remains turned off until the ice bank control three stainless-steel pins are free of ice. Once this happens, the ice bank control module starts the refrigeration com- pressor and the condenser fan motor.

© 2003, IMI Cornelius Inc.

- 3 -

Publication Number: 859000159INS

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Impulse Contact Information Table of Contents Publication Number 859000159INS 2003, IMI Cornelius Inc System Dimensions SafetyRequirements Summary InstallationElectrical Requirements Global ICE Bank Control Gibo Theory of Operation Counter-top InstallationConnect Concentrate and Water Lines Adjust Water-To-Concentrate RatioAdjusting Flow Rates Dispensing Product Water-to-Concentrate Ratio AdjustmentOperations Starting And Stopping the UnitWash Concentrate Systems Daily CleaningDaily Checks Sanitizing Concentrate SystemsSanitize Concentrate Systems Purge Water out of Concentrate Systems Restore OperationWater Flush Concentrate Systems Reference Material Wiring DiagramExternal Carbonator Internal CarbonatorNon-Carbonated Impulse Installation & Operations Manual WATER-TO-CONCENTRATE Ratiotoo LOW or TOO High TroubleshootingOperate Troubleshooting Refrigeration SystemPublication Number 859000159INS 2003, IMI Cornelius Inc Page IMI Cornelius Inc One Cornelius Place Anoka, MN

Non-Carbonated Post-Mix Beverage Dispenser specifications

The Cornelius Non-Carbonated Post-Mix Beverage Dispenser is a revolutionary solution for beverage service, designed to meet the diverse needs of restaurants, cafes, and convenience stores. Renowned for its user-friendly operation and efficient performance, this dispenser stands out in the competitive landscape of beverage dispensing technology.

One of the main features of the Cornelius Non-Carbonated Post-Mix Beverage Dispenser is its ability to serve a variety of non-carbonated drinks, including fruit juices, iced teas, and flavored waters. This versatility makes it suitable for establishments looking to expand their beverage offerings while ensuring quality and consistency. With multiple flavor options, operators can easily customize the drink menu to cater to customer preferences.

The design of the Cornelius dispenser incorporates state-of-the-art technologies that enhance its functionality and reliability. It features a high-efficiency refrigeration system that maintains optimal serving temperatures, ensuring beverages are always fresh and refreshing. The user-friendly interface, complete with an intuitive digital display, allows staff to quickly and accurately select drink options, minimizing wait times for customers.

In terms of operational benefits, the Cornelius Non-Carbonated Post-Mix Dispenser is designed for easy maintenance. Its modular construction allows for rapid component access, reducing downtime during service. The cleaning process is streamlined, facilitating hygiene and compliance with food safety regulations.

Another noteworthy characteristic of this beverage dispenser is its eco-friendly approach. By utilizing a post-mix configuration, it reduces the need for individual packaging, which contributes to lowering environmental impact. This is an important consideration for businesses aiming to adopt sustainable practices.

Moreover, the dispenser’s energy-efficient design plays a crucial role in reducing operational costs. By consuming less power while maintaining peak performance, it enables establishments to manage their operating expenses effectively without sacrificing service quality.

Overall, the Cornelius Non-Carbonated Post-Mix Beverage Dispenser is an exceptional choice for those seeking to enhance their beverage service. With its robust features, advanced technology, and a commitment to sustainability, it provides a competitive edge in today’s fast-paced food and beverage industry. Investing in this advanced dispenser ensures businesses can deliver high-quality, customizable beverages that delight customers and drive sales.
Top Page Image Contents