Cornelius Non-Carbonated Post-Mix Beverage Dispenser specs

Non-Carbonated Impulse Installation & Operations Manual

NOTE: Make sure that the electrical power circuit breaker is switched off or the fuse removed. Before connecting electrical power to the unit, refer to nameplate to verify the power require- ments.

A.Remove the following:

•front merchandiser by removing two screws on the top and lifting up

•key switch wires

•hood by removing two screws on the top and lifting up and forward.

B.Remove second valve from the left to facilitate routing of the new cord.

C.First route the new cord up behind the valve panel and through the cutout in the pump deck. Use the already attached wire tie/fastener on the deck to secure the cord.

D.Connect cord to the receptacle on the refrigeration deck.

E.Turn the circuit breaker on and then the units power switch. Check to see that the agitator motor has started. After about three minutes the compressor should start. If the agitator or compressor do not start call Technical Services.

Connect Concentrate and Water Lines

1.Route concentrate and plain water lines from the back side of the unit and under the unit to the front. Connect them to the appropriate inlet connections.

NOTE: If water supply pressure to the unit is less than 40 psi, a water pressure booster is required. If water supply pressure to the unit is more than 50 psi, a water pressure regulator must be installed in the supply line.

NOTE: A water shutoff valve and water filter in the water supply line are recommended.

2.Make the connection behind the splash panel to the marked 3/8 water tubes.

3.Connect optional drip tray drain hose (if used). Be sure the knock-out in the drip pan has been removed if drain hose is used.

4.Bleed each valve into a bucket until water comes out.

5.Be sure that all concentrate sources are connected and on. Bleed each valve into a bucket until concentrate comes out.

6.Reinstall drip tray and position water bath overflow hose in drip tray indent.

7.Check the system for gas leaks by pressurizing the system and then turning off the cylinder valve. Wait a couple of minutes and check the cylinder gauge to see if the pressure has dropped.

8.Check the system for water and concentrate leaks.

Adjust Water-To-Concentrate Ratio

1.Remove valve front cover and install concentrate diversion assembly in place of nozzle.

Water flow	Concen-
adjuster on	trate diver-
left	sion tube
	Concentrate
	adjuster on
	right

Ratio cup

2.Adjust carbonated water flow to the desired rate (such as 2.50 oz./sec.). Turn the adjuster 1/4 of a turn at a time and recheck the flow.

To increase flow turn clockwise.

3.Adjust the concentrate-to-water ratio of each valve using the concentrate adjuster on the left side of each valve. Hold cup under valve and dispense beverage for a specific time (such as 4 seconds).

Publication Number: 859000159INS

- 4 -

Non-Carbonated Post-Mix Beverage Dispenser specifications

The Cornelius Non-Carbonated Post-Mix Beverage Dispenser is a revolutionary solution for beverage service, designed to meet the diverse needs of restaurants, cafes, and convenience stores. Renowned for its user-friendly operation and efficient performance, this dispenser stands out in the competitive landscape of beverage dispensing technology.

One of the main features of the Cornelius Non-Carbonated Post-Mix Beverage Dispenser is its ability to serve a variety of non-carbonated drinks, including fruit juices, iced teas, and flavored waters. This versatility makes it suitable for establishments looking to expand their beverage offerings while ensuring quality and consistency. With multiple flavor options, operators can easily customize the drink menu to cater to customer preferences.

The design of the Cornelius dispenser incorporates state-of-the-art technologies that enhance its functionality and reliability. It features a high-efficiency refrigeration system that maintains optimal serving temperatures, ensuring beverages are always fresh and refreshing. The user-friendly interface, complete with an intuitive digital display, allows staff to quickly and accurately select drink options, minimizing wait times for customers.

In terms of operational benefits, the Cornelius Non-Carbonated Post-Mix Dispenser is designed for easy maintenance. Its modular construction allows for rapid component access, reducing downtime during service. The cleaning process is streamlined, facilitating hygiene and compliance with food safety regulations.

Another noteworthy characteristic of this beverage dispenser is its eco-friendly approach. By utilizing a post-mix configuration, it reduces the need for individual packaging, which contributes to lowering environmental impact. This is an important consideration for businesses aiming to adopt sustainable practices.

Moreover, the dispenser’s energy-efficient design plays a crucial role in reducing operational costs. By consuming less power while maintaining peak performance, it enables establishments to manage their operating expenses effectively without sacrificing service quality.

Overall, the Cornelius Non-Carbonated Post-Mix Beverage Dispenser is an exceptional choice for those seeking to enhance their beverage service. With its robust features, advanced technology, and a commitment to sustainability, it provides a competitive edge in today’s fast-paced food and beverage industry. Investing in this advanced dispenser ensures businesses can deliver high-quality, customizable beverages that delight customers and drive sales.