Cornelius R-134A Compressor Operates, Continuously but does, Not Form Sufficient ICE Bank

Page 51

Trouble

Probable Cause

Remedy

COMPRESSOR OPERATES

A. Cooling capacity is exceeded

CONTINUOUSLY BUT DOES

by over-drawing.

NOT FORM SUFFICIENT ICE

 

BANK.

 

A.Reduce amount of drinks drawn per given time.

B.Unit located in excessively hot area or air circulation through condenser coil is restricted.

B.Relocate unit or check and if necessary, clean condenser coil as instructed.

NOTE: Ice bank freezes from bottom of evaporator upward. A refrigerant leak or insufficient charge might show an ice bank at bottom and not at top of evaporator.

AGITATOR MOTOR NOT

A.

Power switch (if applicable) in

OPERATING.

 

“OFF”position.

 

B.

Unit power cord or

 

 

refrigeration assembly power

 

 

cord unplugged.

A.Place power switch in “ON”position.

B.Connect power cord(s).

C.No power source (blown fuse or tripped circuit breaker).

C.Replace fuse or reset circuit breaker. (NOTE: Fuse or circuit breaker are not part of Unit).

D.

Agitator motor propeller

D.

Remove obstruction.

 

obstructed.

 

 

E.

Low voltage.

E.

Voltage must be at least 103 volts

 

 

 

(115 VAC unit) or 208 (230 VAC

 

 

 

unit) at compressor terminals

 

 

 

when compressor is trying to

 

 

 

start.

F.

Loose, disconnected, or

F.

Tighten connections or replace

 

broken wiring.

 

broken wiring.

G.

Inoperative agitator motor.

G.

Replace agitator motor.

312027000

46

Page 50 Page 52
Image 51
Page 50 Page 52
Contents This Document Contains Important Information Installation/Service ManualTable of Contents Table of Contents cont’d Compressor Operates Continuously but does not Form Troubleshooting Refrigeration SystemSafety Information Page This page Left Blank Intentionally Unit Description General DescriptionWarranty Reference Information Theory of Operation Flow Diagram FIVE-FLAVOR Unit with BUILT-IN Cold Carbonator Flow Diagram SIX-FLAVOR Unit with BUILT-IN Cold Carbonator This page Left Blank Intentionally Identification of LOOSE-SHIPPED Parts Unpacking and InspectionCutting Hole in Countertop Installing UnitConnecting Plain Water Source Lines to Unit Selecting LocationSyrup Inlet Supply Line Connections SIX-FLAVOR Unit Shown Connecting Syrup Source Lines to Unit Fill Water Tank and Start Refrigeration System Connecting CO2 Source Line to UnitPreparing Unit for Operation Sealing Unit Base to CountertopUnit Unit OperationAdjust WATER-TO-SYRUP Ratio Brix of Dispensed Product 312027000 Daily PRE-OPERATION Check Operating ControlsReplenishing CO2 Supply AdjustmentsCleaning and Sanitizing Unit OperationCleaning CO2 GAS Check Valves Checking ICE Water BathSanitizing Syrup Systems This page Left Blank Intentionally Periodic Inspection Front Access Panel RemovalPreparing Unit for SHIPPING, STORING, or Relocating Hood and Front Panel RemovalDispenser Components SF-1 Dispensing Valve Adjusting Dispensing Valves Water Flow RateUF-1 Dispensing Valve Adjusting WATER-TO-SYRUP Ratio Brix of Dispensed Product Cleaning DROP-IN Refrigeration Assembly Condenser Coil Cleaning Water Tank Water Tank Sanitizing POST-MIX Syrup Systems Wash Syrup SystemsFlush Syrup Systems Water Flush Syrup Systems Sanitize Syrup SystemsPurge Water OUT of Syrup Systems Restore Operation 312027000 Water Strainer Screen and DOUBLE-LIQUID Check Valve Liquid Check Valve Assembly BAG-IN-BOX Syrup System Cleaning CO2 System CO2 GAS Check ValvesSyrup Flavor Change Syrup Tank SystemWiring Schematic for Electronic ICE Bank Control Optional 560001023 301112002 301112002 Wiring Diagram SF-1 Dispensing Valve This page Left Blank Intentionally Troubleshooting POST-MIX System System WATER-TO-SYRUP RatioTOO LOW or TOO High Dispensing Valve Clear But Foams in CUP or Glass Dispensed ProductCarbonation TOO LOW Comes OUTValves Produces Foam AS ITLeaves Dispensing VALVE.CONT’D No Product Dispensed From ALL DispensingTroubleshooting Refrigeration System Agitator Motor not Compressor OperatesContinuously but does Not Form Sufficient ICE BankWarranty Page One Cornelius Place Anoka, Minnesota 612 800
Related manuals
Manual 26 pages 33.21 Kb

R-134A specifications

Cornelius R-134A is a refrigerant commonly used in various cooling and air conditioning applications. It belongs to the hydrofluorocarbon (HFC) family and has become a favored alternative to many ozone-depleting substances. Unlike its predecessors, R-12, which has been phased out due to its detrimental effects on the ozone layer, R-134A offers a more environmentally friendly solution, albeit still having global warming potential.

One of the main features of R-134A is its favorable thermodynamic properties. It exhibits a low boiling point of approximately -26.3°C (-15.3°F), making it suitable for various refrigeration applications, including automotive air conditioning, commercial cooling systems, and domestic refrigerators. Its efficiency is regarded as superior, allowing for quick heat absorption and dissipation. This efficiency translates into energy savings, ultimately benefiting both consumers and manufacturers.

R-134A also boasts a relatively high vaporization heat, demonstrating its effectiveness in heat transfer processes. The low toxicity and non-flammability of R-134A further enhance its appeal, as it poses minimal risk during handling and application. This characteristic makes R-134A safer for technicians and users compared to older refrigerants, which presented higher health hazards.

Within modern technologies, R-134A plays a crucial role in both chiller systems and heat pump applications. It is compatible with various lubricants, allowing manufacturers to utilize R-134A in existing systems with minimal modifications. However, it is essential to use the correct type of oil, as mixing different types can lead to system inefficiencies and potential failure.

Despite its advantages, R-134A has a global warming potential of around 1,430 times greater than carbon dioxide, prompting the refrigerant industry to look for alternatives. Newer refrigerants, such as R-1234yf, offer lower environmental impact, driving a shift towards more sustainable options.

In conclusion, Cornelius R-134A remains a widely used refrigerant known for its efficiency, safety, and effectiveness in heat transfer. While it has played a significant role in the refrigeration and air conditioning industries, the ongoing search for eco-friendly alternatives highlights the need for continued innovation and adherence to environmental standards.
Top Page Image Contents