Tools needed
Electrical requirements
level
3/8" drive 
ratchet
wood floor: 1/8" drill bit
concrete/ceramic floors: 3/16"
tape measure or ruler
Phillips screwdriver
WARNING
Electrical Shock Hazard Plug into a grounded
Do not use an adapter.
Failure to follow these instructions can result in death, fire, or electrical shock.
Recommended ground method
For personal safety, this range is equipped with a power supply cord having a
If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have a properly polarized and grounded,
15/16" | channel lock | |
pliers | ||
and 3/8" |
| |
combination |
| |
wrenches |
| |
stainless |
| |
steel/glass |
| |
mirror |
| |
putty knife |
| |
| gloves | |
safety glasses |
| |
hand or | pipe | |
wrench | ||
electric drill | ||
|
Materials required:
•gas line shutoff valve
•1/2" male pipe thread nipple for connection to pressure regulator
•L.P.
•AGA or CSA
•Insulated pad or 1/4" plywood if range is installed over carpeting
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate and that the outlet is correctly polarized.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not sure range is properly grounded.
A
Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. In addition to checking that the outlet is correctly grounded, the outlet must be checked by a qualified electrician to see if it is wired with correct polarity.
Important: This range is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized.
A wiring diagram is included on the back of the range.
See “Cabinet dimensions/requirements,” Page 2, for recommended location of electrical outlet.
electrician.
Copies of the standards listed may be obtained from:
*National Fire Protection Association One Batterymarch Park
Quincy, Massachusetts, 02269
ground prong
power supply cord
Gas supply requirements
WARNING
Explosion Hazard
Use a new AGA or CSA approved gas supply line.
Install a
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure gas pressure does not exceed 14" water column. Examples of a qualified person include licensed heating personnel, authorized gas company personnel, and authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
This installation must conform with local codes and ordinances. In the absence of local codes, installations must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 — latest edition**.
Input ratings shown on the model/serial rating plate are for elevations up to 2,000 feet. For assistance when installing the range at higher elevations, contact your local service company.
Type of gas: This range is
This range is factory set for use with Natural gas. Gas conversion instructions are provided on pages
Gas supply line: Provide a gas supply line of 3/4" rigid pipe to the range location. With L.P. gas, piping or tubing size can be 1/2" minimum. A smaller size pipe on longer runs may result in insufficient gas supply. Usually, L.P. gas suppliers determine the size and materials used in the system.
Flexible metal appliance connector: If local codes permit, a new AGA or CSA
Rigid pipe connection: Requires a combination of pipe fittings to obtain an
manual shutoff valve
“open” position
to range
gas supply
Shutoff valve: The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room as the range and should be in a location that allows ease of opening and closing. The valve is for turning on or shutting off gas to the range. Do Not block access to shutoff valve.
Pressure regulator: The gas pressure regulator supplied with this range must be used. The inlet pressure to the regulator should be as follows for proper operation:
NATURAL GAS:
Minimum pressure: 5 inches W.C.
Maximum pressure: 14 inches W.C.
L.P. GAS:
Minimum pressure: 11 inches W.C.
Maximum pressure: 14 inches W.C.
Contact local gas supplier if you are not sure about the inlet pressure.
Line pressure testing above 1/2 psi gauge
(14" WCP) — The range and its individual manual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of that system at test pressures greater than 1/2 psig (3.5 kPa).
Line pressure testing at 1/2 psi gauge (14" WCP) or lower — The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of that system at test pressures equal to or less than 1/2 psig (3.5 kPa).
Copies of the standards listed may be obtained from:
**CSA International
8501 East Pleasant Valley Road Cleveland, Ohio
Page 3