Electrolux - Gibson 241512200A warranty Before Installing The Water Supply Line, You Will Need

Page 5

Installation - Connecting Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

•Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for any damage if plastic tubing is used for supply line.

•DO NOT install water supply tubing in areas where temperatures fall below freezing.

•Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

•Access to a household cold water line with water pressure between 20 and 100 psi.

•A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

•A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

•A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6 meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.

7.Coil excess water supply line (about 2½ turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/OFF position of arm).

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Us e & Care Manual Please Read and Save These Instructions Welcome & CongratulationsFor Your Safety Important Safety InstructionsChild Safety Proper Disposal of Your Refrigerator or FreezerInstallation To Connect Water Supply Line To Ice Maker Inlet Valve Before Installing The Water Supply Line, You Will NeedDoor Removal Instructions Door Removal InstructionsTo Remove Refrigerator Door To Remove Freezer DoorFeatures At a Glance Refrigerator & Freezer Controls Temperature Adjustment Temperature ControlsTemperatures gradually move the knob in small Increments, allowing the temperature to stabilizeTo adjust cantilever shelves Cantilever Shelf AdjustmentLooking Inside TIP-UP Shelf Some ModelsHumidity Control Some Models Adjustable Door BinsCrispers Some Models Deli Drawer Some ModelsAutomatic Ice and Water Dispenser How the Water Dispenser Works ICE and Water Dispenser FeaturesHow the Ice Dispenser Works ICE Dispenser TipsRemove and empty the ice storage bin if Cleaning the ICE DispenserGibson TM * Ice and Water Filter some models Energy Saving Ideas Food Storage & Energy Saving IdeasFood Storage Ideas Normal Operating Sounds & Sights Care & Cleaning Replacing Light Bulbs Gibson Refrigerator Platinum Advantage Warranty Warranty InformationRefrigerator Warranty Canada Before You Call Temperatures are TOO ColdRunning of Refrigerator OPENING/CLOSING of DOORS/DRAWERSWATER/MOISTURE/FROST Inside Refrigerator Temperatures are TOO WarmWATER/MOISTURE/FROST Outside Refrigerator Automatic ICE MakerWarm ICE DispenserOdors in Refrigerator Water DispenserOPENING/CLOSING of DOORS/DRAWERS Light Bulb is not on

241512200A specifications

Electrolux has been a trusted name in home appliances for decades, and the Gibson 241512200A is a prime example of their commitment to quality and innovation. This model combines versatility with advanced technology to elevate the cooking experience, making it an ideal choice for modern kitchens.

One of the standout features of the Gibson 241512200A is its spacious design. With a generous interior capacity, this appliance can accommodate large dishes, making it particularly suitable for families or those who enjoy entertaining. The thoughtful layout allows for easy organization and access, so users can find their cooking essentials without hassle.

The Gibson 241512200A utilizes advanced cooking technologies that enhance its performance. It features precise temperature control, which ensures that food cooks evenly and to perfection. This is especially important for baking and roasting, where consistent heat is critical. Additionally, the appliance incorporates innovative heating elements that contribute to faster cooking times, saving users valuable time in the kitchen.

Another remarkable technology integrated into the Gibson 241512200A is its user-friendly interface. The digital control panel is intuitive, allowing users to adjust settings with the touch of a button. This feature is complemented by a variety of cooking presets, which simplify meal preparation by automatically setting optimal cooking times and temperatures for different dishes.

Safety is also a major consideration in the design of the Gibson 241512200A. The appliance comes equipped with features such as an automatic shut-off function that provides peace of mind, especially for busy households. The cool-touch exterior ensures that the surface remains safe to touch during and after cooking, minimizing the risk of burns.

In terms of energy efficiency, the Gibson 241512200A excels as well. It is designed to consume minimal energy without compromising performance, making it an environmentally friendly option for consumers looking to reduce their carbon footprint.

In conclusion, the Electrolux Gibson 241512200A stands out due to its combination of spacious design, advanced cooking technologies, user-friendly interface, safety features, and energy efficiency. This appliance truly encapsulates what a modern kitchen needs, making it an essential tool for both novice cooks and seasoned chefs alike. Its blend of functionality and innovation ensures that users can enjoy a seamless cooking experience, resulting in delicious meals for family and friends.
Top Page Image Contents