Whirlpool GY397LXUS manual Range Care, Self-CleaningCycle

RANGE CARE

Self-CleaningCycle

WARNING

Burn Hazard

Do not touch the oven during the Self-Cleaning cycle.

Keep children away from oven during

Self-Cleaning cycle.

Failure to follow these instructions can result in burns.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the Self-Cleaning cycle. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well-ventilated room.

Self-clean the oven before it becomes heavily soiled. Heavy soil results in longer cleaning and more smoke.

Keep the kitchen well-ventilated during the Self-Cleaning cycle to help get rid of heat, odors, and smoke.

Do not block the oven vent(s) during the Self-Cleaning cycle. Air must be able to move freely. Depending on your model, see “Oven Vent” or “Oven Vents” section.

Do not clean, rub, damage or move the oven door gasket. The door gasket is essential for a good seal.

Prepare Oven:

■Remove the broiler pan, grid, cookware and bakeware and, on some models, the temperature probe from the oven.

■Remove any foil from the oven because it may burn or melt, damaging the oven.

■Remove oven racks to keep them shiny and easy to slide. See “General Cleaning” section for more information.

■Hand clean inside door edge and the 1½" (3.8 cm) area around the inside oven cavity frame, being certain not to move or bend the gasket. This area does not get hot enough during self-cleaning to remove soil. Do not let water, cleaner, etc. enter slots on door frame. Use a damp cloth to clean this area.

■Wipe out any loose soil to reduce smoke and avoid damage. At high temperatures, foods react with porcelain. Staining, etching, pitting or faint white spots can result. This will not affect cooking performance.

Prepare Cooktop and Storage Drawer:

■Remove plastic items from the cooktop because they may melt.

■Remove all items from the storage drawer.

NOTE: Oven temperature must be below 400°F (205°C) to program a clean cycle.

How the Cycle Works

IMPORTANT: The heating and cooling of porcelain on steel in the oven may result in discoloring, loss of gloss, hairline cracks and popping sounds.

The Self-Cleaning cycle uses very high temperatures, burning soil to a powdery ash.

The oven is preset for a 3 hour clean cycle, however the time can be changed. Suggested clean times are 2 hours for light soil and between 3 hours and 4 hours for average to heavy soil.

Once the oven has completely cooled, remove ash with a damp cloth. Do not wipe down any of the inside surfaces until the oven has completely cooled down. Applying a cool damp cloth to the inner door glass before it has completely cooled could result in the glass breaking.

The oven light will not work during the Self-Cleaning cycle.

When “LOCK” shows in the display, the door cannot be opened. To avoid damage to the door, do not force the door open when ”LOCK” is displayed.

To Self-Clean:

1.Close the oven door.

2.Press SELF CLEAN. “CLEAN” and “SEt” will flash in the display.

3.Press the PRESETS 0 number pad.

MEd (Medium soil, 3 hours) appears in the display.

If the door is not closed, beeps will sound and “door” will appear in the display until the door is closed. If the door is not closed within 30 seconds, the self-cleaning operation will be canceled and the display will return to the time of day.

If more than 5 seconds elapse between pressing Clean and Presets 0, the program will automatically return to the previous display.

4.To choose a clean setting other than medium, press the PRESETS 0 number pad to scroll through the self-cleaning settings.

HVy (heavy soil, 4 hours) MEd (medium soil, 3 hours) LITE (light soil, 2 hours)

Choosing the soil level of the oven automatically programs the self-cleaning time.

5.After 4 seconds, the oven will start cleaning.

“CLEAN” will appear in the display. “LOCK” will flash in the display, once the door locks, “LOCK” will remain lit. The cleaning time will count down in the display.

To Delay Start Self-Clean:

Before delay starting Self-Clean, make sure the door is closed completely or it will not lock and the cycle will not begin.

1.Press DELAY 1 number pad.

“DELAY” and “00:00” will flash in the display.

2.Using the number pads, enter the amount of time you want to delay the cycle. Delay time can be set from 10 minutes (00:10) to 11 hours and 59 minutes (11:59).

3.Press SELF CLEAN.

“SET” flashes in the display.

14