Aga Ranges DC6 (FFD) owner manual Installation

Page 5

INSTALLATION

CAUTION: THIS INSTALLATION MUST CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES WITH THE NATIONAL FUEL GAS CODE, ANSI Z223.I/NFPA 54 AND NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (IN CANADA CAN/CGA-B149) AND ONLY USED IN A WELL VENTILATED SPACE, READ THESE INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE.

PRIOR TO INSTALLATION, ENSURE THAT THE LOCAL DISTRIBUTION CONDITIONS (NATURE OF GAS AND GAS PRESSURE) AND THE ADJUSTMENTS OF THE APPLIANCE ARE COMPATIBLE.

THE GAS ADJUSTMENT CONDITIONS FOR THIS APPLIANCE ARE STATED ON THE DATA PLATE WHICH IS SITUATED IN THE CENTRE VENT SLOT NEAR THE BASE OF THE FRONT PLATE.

This appliance is not connected to a combustion products evacuation device. it shall be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.

It should be in accordance with any relevant requirements of the Gas Region and Local Authority.

The appliance must be disconnected from the gas supply piping system during any pressure testing of that system test pressure in excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply system at test pressures equal to or less than 1/2 psi (3.5 kPa).

On completion, test the gas installation for soundness and purge. Leak testing of the appliance shall be conducted according to the manufacturer’s instructions.

NOTE: Use soapy water solution on new gas connections to ensure there are no gas leaks.

WARNING: ELECTRIC SHOCK HAZARD

It is the customers responsibility to contact a qualified electrical installer to make sure the electrical installation is adequate and in conformance with National Electrical Code ANSI/FPA 70-latest edition, and all local codes and ordinances.

Take special care when cutting holes in walls or floor. Electrical wires may be behind the wall or floor covering and could cause an electrical shock if you touch them.

Locate any electrical circuits that could be affected by the installation of this product and disconnect power circuit.

Electrical ground is required on this appliance.

Do not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock.

Do not use an extension cord with this appliance.

Check with a qualified electrician if you are not sure the appliance is properly grounded.

Failure to follow these instructions could result in death or serious injury.

5

Image 5
Contents AGA SIX-FOUR Series DC6 FFD Natural GAS and Propane GAS Contents Installation Section Technical Data Installation Fitting and Product Dimensions Electrical Connection Electrical Connection Connecting to GAS Location Installation Must Conform with the National Electric CodeSide View Cooker StabilityPressure Testing Levelling and Mobility Wheels INSTALLATION/LEVELLINGHotplate Castings Fitting of Hotplate Casting and PAN SupportsUltra Rapid Burner WOK Burner Fitting Burner CAP Rapid and SEMI-RAPID Burners Assembly of Rapid and SEMI-RAPID BurnersDesn 512995 a Handrail Fitting To Adjust PAN Support LevelSplashback Users Guide General Information Important Notice Please Read the Accompanying WarrantyChild Safety Safety Precautions and HintsDesn 512646 B Control Panel To USE the Hotplate GAS HotplateImportant Safety Considerations To FIT PAN Supports Setting the Time of DAY Setting UP the Cooker for USESimmering Oven Using the Simmering Oven SettingSimmering Oven Storage and RE-HEATING of FoodBaked Potatoes Ideas for the Simmering OvenRecipes Ragout of Beef in Ale Bread and Butter Pudding Recipes Roast fillet of LambDauphinoise Potatoes Gammon and Apricot Pie RecipesBraised Red Cabbage St Clements PuddingFrangipane and Apple Pudding Meal RecipesChilli Con Carne Broiling Oven Food Suggested Heat SettingCondensation OvensGeneral Deep Fat Frying Oven Cooking GuideCooking Hints Roasting Oven Yeast Mixture Food Setting F Shelf Position Approximate Cooking TimeBaking Oven Food Setting FYeast Mixtures Food Setting F Approximate Cooking TimeSetting the Minute Timer Minute TimerSetting AN END Time only , Automatically Setting the Automatic Cooking ProgramCancelling a Program Automatic Cooking ControlKEY Lock Cleaning & Caring for Your CookerTo Activate Keylock Function To DE-ACTIVATE KeylockDo not USE Abrasives Cooker Part and Finish Cleaning MethodPOWDERS, Soap Filled Pads Wire Do not USE ANY Cleaning MaterialWOOL, Spray CLEANERS, BRUSH-ON Which MAY Clog the PoresOven Shelves These shelves are designed to slide out Fitting Burner CAP Rapid and SEMI-RAPID Assembly of Rapid and SEMI-RAPID BurnerUltra Rapid Burner Servicing Section Completely Isolate from Electric Supply Before Servicing ServicingDesn 512393 C To Remove Facia Castings To Remove Side PanelsTo Remove Handrail see FIG To Remove TimerTo Remove GAS TAPS/IGNITION Switches To Remove Spark Generator To Remove Grill RegulatorTo Remove Oven Thermostats To Remove Electrodes LH Burner To Remove Electrodes LHR, CF, CR, RHR, RHF BurnersTo Remove Thermocouple LHF Burner To Remove Oven and Broiler Liners see FIG To Remove Thermocouple LHR, RHR, RHF BurnersTo Remove Oven FAN To Remove Elements RH OvensTo Remove FAN Oven Element

DC6 (FFD) specifications

The Aga Ranges DC6, an exemplary model in the Aga collection, is a testament to the brand's legacy of combining traditional craftsmanship with modern culinary technology. This cast iron range cooker is designed for those who appreciate both aesthetics and functionality, resonating with home chefs and culinary enthusiasts alike.

One of the hallmark features of the Aga DC6 is its iconic cast iron construction, which is renowned for its excellent heat retention and even cooking. The cooker is designed to maintain a consistent temperature, allowing for perfectly cooked meals whether roasted, baked, or simmered. This characteristic makes it particularly appealing for slow cooking and batch preparation.

The DC6 model boasts six cooking ovens, offering versatility and options for various culinary tasks. Each oven operates at different temperatures, allowing chefs to prepare multiple dishes simultaneously. The design includes a roasting oven, a baking oven, and a simmering oven, catering to diverse cooking methods and preferences. This multi-oven setup ensures that users can maximize efficiency in the kitchen without sacrificing quality.

Furthermore, the Aga DC6 incorporates advanced technology to enhance user experience. The integrated control panels feature intuitive interfaces that simplify the cooking process. Users can easily adjust temperature settings and monitor cooking progress, making it suitable for cooks of all skill levels.

Another remarkable characteristic of the DC6 is its energy efficiency. The range is designed to minimize energy consumption without compromising performance. It employs modern insulation techniques that limit heat loss, ensuring that the ovens remain hot and ready for use while reducing overall energy expenditure.

Aesthetically, the Aga Ranges DC6 excels as well. Available in a range of colors and finishes, it can fit seamlessly into any kitchen décor. Its timeless design elevates the aesthetic appeal of the kitchen, serving as both a cooking appliance and a statement piece.

In conclusion, the Aga Ranges DC6 is a perfect blend of traditional craftsmanship and modern innovation. With its cast iron construction, multiple ovens, user-friendly technology, and energy efficiency, it appeals to both professional chefs and home cooks, making it a sought-after appliance in today's kitchens.