AUTOMATIC ICE AND WATER DISPENSER
PURESOURCE MB ICE AND WATER FRONT FILTER (SOME MODELS)
NOTE
If you purchased a refrigerator with a PureSource MB Ice and Water front filter, please read the following use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It is located in the upper right front corner of the refrigerator compartment.
System Startup:
Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter.
The filter cartridge has already been installed in the filter housing at the factory. Refer to the How To Prime The Water Supply System section to properly fill the system with water.
Order new filter cartridges through the dealer where you bought the refrigerator, contact the Electrolux Solutions Hotline at 1-
The PureSource MB Ice and Water Filter System MBFC 2003 with the PureSource MB cartridge MB100 is tested and cer tified by NSF International, the nationally recognized and respected, not for profit, certification organization
for public health safety. The PureSource MB Filter system is tested and certified to ANSI/NSF Standards 42 and 53. See performance data sheet for specifications. PureSource MB,
•Rated Capacity - 250 gallons
•Rated service flow
•Maximum Rated Pressure - 100 PSI
•Maximum Operating Temp. - 100° F
Changing the Filter:
Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. Ice jams in the ice maker and/or hollow ice cubes (partially frozen cubes with liquid water inside), may also
be a sign that your water filter needs changing. The Filter Status light will turn red after approximately 250 gallons of water hasflowed through the ice and water dispenser. Also, if the filter has been in a refrigerator that has not been in use for awhile (during moving for example), change the filter before reinstalling the refrigerator. The dispenser system will also operate without filtration (with filter cartridge removed and bypass installed).
To change filter:
It is not necessary to turn the water supply off to change the filter.
1.Turn OFF side mounted ice maker by raising wire signal arm to the UP position. Turn OFF rear mounted ice maker by pressing ON/OFF power switch to the “O” position.
2.Push the Filter Release Button, located to the right of the filter cartridge, to release the filter from the housing. To minimize the possibility of the filter falling out of the housing during removal, it would be best to hold the filter as it moves out toward you.
3.Pull the old filter cartridge straight out of the housing.
NOTE
A small amount of water may be released during this operation. You should have a paper towel or dish cloth handy to wipe up any water that may drip out of the filter or housing. Two small holes near the back of the housing have been added for any excess water to escape. It would be best to clear away any food near this area on the top shelf in advance of removing the filter.
4.Discard the old filter.
5.Remove the new filter cartridge from the packaging and insert into the filter housing the same way the old one came out.
6.When the cartridge is almost in, you will feel it stop against the clip assembly in the back of the housing. The clip assembly holds the filter cartridge firmly in place. At this point, you will need to push firmly until the cartridge snaps fully in place. When completely in place, the front of the filter cartridge will be flush with the front of the housing.
7.Replace the ice container. Turn ON side mounted ice maker by lowering wire signal arm to the DOWN position. Turn ON rear mounted ice maker by pressing ON/OFF power switch to the “I” position.
8.Fill a glass with water. As you are doing this, check for leaks at the filter housing.
9.To prime filter system and purge air from water line, continue flushing the system for approximately 3 minutes to assure that the purest water possible is stored in the water tank. There will be noticeable spurts and sputters as the system pushes air out through the system and out the dispenser nozzle. This is normal.
IMPORTANT
Resetting The Filter Status Light (some models)
After replacing the filter cartridge, it will be necessary to press the Filter Reset button located on the ice and water dispenser. This will reset the Filter Status light. Push the reset button until the green, red and amber lights flash
20