QSC Audio CM16a manual Introduction- Network Description

Page 14

Section 1: Introduction- Network Description

QSC CM16a Amplifier Network Monitors are designed to operate on standard 10BASE-T Ethernet. Each CM16a operates as a respective node on its network; each unit contains a programmable IP address in nonvolatile memory. To minimize network conflicts, each IP address should be unique. When shipped from the factory, the CM16a’s factory-programmed IP address is printed on a label affixed to the front panel of the unit. Record the unit’s IP address and serial number and keep in a safe place. Ethernet devices such as hubs, repeaters, switches and routers will usually afford the flexibility to configure the network as needed.

The system controller computer on the network must have an Ethernet-compatible network interface card (NIC) installed. Additionally, if operation during power outage or interruption is required, an uninterruptable power supply (UPS) will be required for the host computer , CM16a, and any hubs, switches or repeaters. If the CM16a is disconnected from the network for any reason, it will continue to process audio using the last settings, assuming AC power is uninterrupted.

The CM16a connects to the network via its RJ-45 connector on the rear panel. This allows direct connection to a 10BASE-T network. Use Category 3 (or better) unshielded twisted pair (UTP) Ethernet Cable. Most ready-made Ethernet patch cables available today are rated at least Category 5 making them suitable for this application.

One side note regarding Ethernet cabling: Although Category 3 data cable is called out as the minimum requirement, it is increasingly difficult to find. Higher grades of cable are becoming the “normal stock” with the proliferation of 100BASE-T Ethernet. Category 5 Ethernet cable is the most widely available type of data cabling as of this writing. So what does this mean? Use Category 3 if it is available and cost effective. If the cost of Category 5 cable is not prohibitive, it may be desirable to do your cabling runs with Category 5 due to its increased data rate capabilities. The extra capability may be needed for future system expansion where 100 BASE-T devices are used. 10BASE-T capability is all that is required for the CM16a and thus the call out for Category 3 as the minimum.

14

Image 14
Contents CM16a Amplifier Network Monitor ¨ Warning ¨ Table of Contents CM16a Amplifier Network Monitor Federal Communications Commission FCC Information Introduction- Overview Series are not supported by the CM16aIntroduction- Physical Characteristics & Layout Physical CharacteristicsIntroduction- Physical Layout Diagram RS-232 port for network and firmware utilitiesIntroduction- List of Functions & Features Functional LISTING, Block Diagram & Detailed DescriptionsIntroduction- Block Diagram part Introduction- Block Diagram part Introduction- Detailed Description of Functions Introduction- Detailed Description of Functions Amplifier Monitoring FunctionsRS-232 Port Functions Introduction- Network Description Introduction- Sample Network Topologies Introduction- Sample Network Topologies Unpacking Installation- Basics and MountingWhat is Included in the Carton Location ConsiderationsInstallation- Mounting and AC Power Connecting AC PowerInstallation- Connections Connecting Audio InputsConnecting the RLY OUT Connecting page InputConnecting the RLY/TRG Connecting the Monitor Chain IN/OUTConnecting to 4-CHANNEL Amplifiers Connecting to the RS-232 PortConnecting to 2-CHANNEL Amplifiers Installation- Rear Panel Detail Operation- LED Indicators Port Connected LED’sOperation- General Information & Presets START-UP Behavior and Preset OperatingOperation- Recalling Presets Using RLY/TRG Most up-to-date informationHOW to put the CM16a into Bypass Mode #2 Operation- Bypass Modes and Switch LocationHOW to put the CM16a into Bypass Mode #1 RS-232 Communications Procedure Operation- Serial Port I/O InterfaceXon/Xoff IP Address Assignment Only Required for Attaching to Existing NetworksOperation- Telnet Access This is the basic procedure for opening a Telnet sessionOperation- Fuse Replacement Fuse ReplacementSpecifications- Dimensions Power amplifier output processing SpecificationsInput Signal Processing Contact closure inputs and outputs Power amplifier managementControl room foldback monitoring RS232 Port GeneralARCHITECT’S and ENGINEER’S Specifications Appendix- Ethernet Cable Pinouts Ethernet CablingRS-232 Pinout Appendix- DataPort Pin-out & Connector P-N’sPin Signal Description How to Contact QSC Audio Products
Related manuals
Manual 40 pages 2.28 Kb

CM16a specifications

The QSC Audio CM16a is a versatile and powerful amplifier designed to meet the demands of professional audio applications. Known for its reliability and performance, the CM16a is ideal for both live sound and installation scenarios, offering a perfect blend of advanced technology and user-friendly features.

One of the standout features of the CM16a is its Class D amplifier architecture. This technology ensures not only high efficiency but also a lightweight design, making it easier to transport and install in various settings. The amplifier delivers an impressive output power of 1600 watts at 4 ohms, providing ample headroom for demanding audio applications. The CM16a is capable of handling multiple speaker configurations, making it a flexible choice for various setups.

Another key characteristic of the QSC CM16a is its advanced thermal management system. This built-in feature ensures the amplifier operates within safe temperature limits, enhancing reliability and extending the lifespan of the unit. The CM16a also includes an intelligent protection circuit that safeguards the amplifier from overload and short circuits, allowing users to operate it confidently even during intense performances.

The CM16a comes equipped with multiple inputs and outputs, including XLR and TRS connectors, enabling seamless integration with a range of audio sources and systems. This versatility allows for easy connection to mixers, microphones, and instruments, making it suitable for diverse applications from concerts to corporate events.

In addition to its robust performance, the QSC CM16a features an intuitive front panel design with LED indicators for quick monitoring of system status and performance. Users can easily adjust levels and settings, ensuring optimal audio quality for any given situation.

The amplifier is also designed with efficiency in mind, incorporating Power Factor Correction (PFC) technology. This enhances power usage, reducing operational costs while minimizing environmental impact.

In conclusion, the QSC Audio CM16a stands out as a premier choice for audio professionals seeking a reliable, high-performance amplifier that can deliver exceptional sound quality. With its Class D technology, advanced protection features, versatile connectivity, and user-friendly design, the CM16a is a worthy investment for any audio application. Whether for live sound reinforcement or permanent installations, the CM16a promises to meet the needs of even the most demanding audio environments.