QSC Audio CX502, CX602V, CX404, CX902, CX702, CX204V, CX1102, CX1202V, CX302V, CX254 后面板, 机架安装, 交流电源连接

Page 43

后面板

（所示为 CX404，其它型号相似，2 通道 型也配有 XLR 输入）

1- 通道 1 接线盒输入连接器

5- 阻挡跨接片输出连接器

2- 数据埠连接器

6- 冷却进风口

3-CH2 接线盒输入连接器

7- 模式转换器设置图

4- 模式转换器

8-IEC 电源连接器

机架安装

按如下所示的步骤安装： 用四颗螺丝和垫圈将放大 器安装到设备机架导轨上。要在机架外使用放

大器，需在底部装上自粘性橡胶脚垫。

冷却

空气从机架流入放大器后面，从前面流出。 这可使机架冷却。放大器工作量增大时，风 扇自动加大转速。

不要挡住前面或后面的通风口！

CH

QSC 放大器中的气流：冷却风扇将冷空气 吸入放大器的后部。热风从放大器前盖流 出。

交流电源连接

连接交流电源到放大器后面的 IEC 插槽。注意：在连接交流电源前需关闭交流电源开关。要使用远程控制系统 或待机功能，必须打开交流电开关。

正确的交流线压在后面板的序列号标签上注明。连接错误的线压会损坏放大器或增加电击危险。

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Volt Direct Output Models CX204V 4-channel CX302V 2-channel TD-000077-00FCC Interference Statement Important Safety Precautions & Explanation of SymbolsUnpacking IntroductionFront Panel AC Mains Connection Rear PanelRack Mounting CoolingSetting Low Frequency Filters Setting the Mode SwitchesSetting Clip Limiters Selecting Stereo, Parallel, or Bridge ModeDataPort Tips Terminal Block ConnectorsDataPort InputsLoads Rated by Model OutputsLow Impedance Outputs Distributed Outputs V models, 70V/140VAbnormal indication LED IndicatorsBrdg and PAR Gain Control Security Plate Gain ControlsInput Specifications 2-Channel Low-Impedance ModelsInput SENSITIVITY, Vrms CONTROLSFrontCX254 Specifications 4-Channel Low-Impedance ModelsCX204V CX302V CX602V CX1202V Specifications 2- and 4-Channel Distributed 70V Line ModelsCurrent Draw Table in Amperes Thermal Loss TableVAC models, multiply values shown by Declaración DE LA FCC Respecto a LA Interferencia Desembalaje IntroducciónPanel frontal Conexión a la línea principal de CA Panel posteriorMontaje en bastidor EnfriamientoAjuste de los filtros de baja frecuencia Ajuste de los conmutadores de modoAjuste de los limitadores de recorte Selección del modo Estéreo, Paralelo o PuenteadoConectadores del bloque de terminales DataPortEntradas Sugerencias sobre el DataPortCargas clasificadas por modelo SalidasSalidas de baja impedancia Salidas distribuidas modelos V, 70V/140VRecorte ROJO, adyacente a las marcas de números del canal Indicadores LEDPlaca de Seguridad del Control de Ganancia Controles de GananciaTabla de gasto de corriente en amperios Tabla de pérdida térmicaCómo comunicarse con QSC Audio Products Déclaration DE LA FCC Relative AUX Interférences Précautions importantes et explication des symbolesDéballage IntroductionPanneau avant Branchement de l’alimentation secteur ~ Installation sur bâtiPanneau arrière RefroidissementRéglage des filtres basse fréquence Réglage des commutateurs de modeSélection du mode Stéréo, Parallèle ou Pont Réglage des limiteurs d’amplitudeEntrées XLR modèles à 2 canaux seulement Conseils relatifs aux connecteurs DataPortEntrées Connecteurs de bornierCharges nominales indiquées par modèle SortiesSorties à faible impédance Sorties distribuées modèles V, 70 V/140Clip ROUGE, adjacent aux numéros de canaux VoyantsCouvercle de Sécurité des Commandes de Gain Commandes de GainTableau d’appel de courant en ampères Tableau de déperdition de chaleurComment prendre contact avec QSC Audio Products FCC-HINWEIS ZU Empfangsstörungen Wichtige Sicherheitsvorkehrungen und SymbolerklärungAuspacken EinführungFrontplatte Netzanschluss RückplatteRack-Einbau KühlungEinstellen der Niederfrequenzfilter Einstellen der BetriebsartenschalterEinstellen der Clipbegrenzer Auswahl des Stereo-, Parallel- oder ÜberbrückungsmodusXLR-Eingänge nur bei 2-Kan.- Modellen EingängeTipps zum Gebrauch des DataPort KlemmenleistenanschlüsseNennlasten nach Modell AusgängeNiederohmige Ausgänge Verteilte Ausgänge „V-Modelle, 70 V/140Normalanzeige Netzschalter EIN LED leuchtet auf LED-AnzeigenVerstärkungsregler-sicherheitsplatte VerstärkungsreglerStromaufnahmetabelle in Ampere WärmeverlusttabelleKontaktinformationen für QSC Audio Products 不要堵塞通风口。 不要安装在会产生热量的设备附近，如散热器、热调节装置、炉子或者其他设备 （包括放大器）。 重要的安全注意事项和符号说明非常感谢您购买 QSC 功率放大器。请阅读以下说明，以获得产品的最佳效果。 CX 型号的连线特点： 前面板机架安装 后面板交流电源连接 设置削波限制器 设置模式切换器输入端 数据埠低阻抗输出 输出端异常显示： LED 指示灯增益控制安全板 增益控制热损表 联系 QSC Audio Products 最大电流表 （单位：安培）Page Page Mailing address
Related manuals
Manual 2 pages 6.05 Kb

CX302, CX1202V, CX502, CX702, CX1102 specifications

QSC Audio has established itself as a leader in professional audio solutions, and their CX series amplifiers, including the CX204V, CX254, and CX404, stand out for their performance and versatility. These amplifiers are specifically designed to meet the needs of commercial audio applications, such as in venues, corporate environments, and educational institutions.

The CX204V is a 2-channel amplifier that delivers 200 watts per channel at 4 ohms, making it ideal for smaller venues or installations that require high-quality audio without overwhelming power. One of its key features is the inclusion of built-in DSP (Digital Signal Processing) capabilities, allowing users to optimize their sound with advanced filtering and equalization options. Additionally, the amplifier supports a range of input options, including balanced XLR and 1/4-inch connectors, providing flexibility for various audio setups.

Moving to the CX254, this 2-channel amplifier boosts power output to 250 watts per channel at 4 ohms, making it suitable for larger spaces that necessitate a bit more oomph. The CX254 also includes QSC’s Power Factor Correction technology, which ensures efficient power usage and greater amplification performance, even during demanding situations. Furthermore, it features RS-232 control capabilities, providing users with remote operation options and making integration into existing audio systems seamless.

The CX404 takes things a step further with its 4-channel configuration, delivering 200 watts per channel at 4 ohms. This amplifier is particularly well-suited for multi-zone applications where audio needs to be distributed across various areas. With its advanced overheating protection and short-circuit protection features, the CX404 is built for durability and reliability, ensuring consistent performance without the risk of damage during extended use.

All three amplifiers in the CX series include QSC's innovative Class D topology, offering lightweight and compact design without sacrificing power or audio quality. The CX series is also distinguished by its robust construction, including a rugged chassis designed to withstand the rigors of installation and performance use.

In summary, the QSC Audio CX204V, CX254, and CX404 seamlessly combine power, efficiency, and versatility, making them ideal choices for a variety of commercial audio applications. Their built-in technologies, advanced features, and solid construction emphasize QSC’s commitment to delivering exceptional sound experiences.
Top Page Image Contents