QSC Audio DCA Series Introduction & Description of Each Model, Description of each model

Page 4

INTRODUCTION & DESCRIPTION OF EACH MODEL

Introduction

This manual covers setup and operation of cinema crossover accessories for QSC DCA Digital Cinema Amplifiers. There are three models: the XC-3 crossover, the LF-3 low frequency filter, and the SF-3 subwoofer filter. Together with DCA amplifiers, they allow you to assemble any type of cinema sound system, mono or multi-channel.

Each accessory mounts directly to the back of the amplifier by plugging into the amplifier’s DataPort and is secured with three screws. Operating power and all connections between the accessory and amplifier are provided by the DataPort connection.

Frequency and delay parameters are user-adjustable by inserting selected 8-pin SIP resistor networks into sockets on the underside of the accessory. A DIP switch permits selection of functions such as delay and high-frequency boost, depending upon model. Each accessory includes an assortment of the proper SIP resistor networks and three mounting screws. Keep the unused SIPs for future use.

Description of each model

XC-3This accessory is a two-way crossover, with the low frequency band fed to channel 1 of the amplifier and the high frequencies to channel 2. An all-pass filter on the low frequency band delays the audio signal, permitting time alignment of a cone driver with a high-frequency horn. A selectable high-frequency boost circuit provides several increments of compensation for screen loss or constant-directivity horn equalization. A HF trim control provides 0 to 20 dB of attenuation for matching levels between frequency bands.

The XC-3 can be used by itself with one amplifier for a 2-way system (shown opposite page, bottom-left), or with the LF-3 and an additional amplifier for 3-way systems, as shown, opposite page, bottom-right. The XC-3 has a pass-through output in parallel with the input for distributing the audio signal to the LF-3. The filter circuitry uses a 4th-order Linkwitz-Riley alignment with 24 dB/octave slopes.

LF-3Used in a system with the XC-3, the LF-3 performs the low-frequency crossover functions in a 3-way system as shown, opposite page, bottom-right. Unlike the XC-3, it has two discrete channels; one LF-3 with an amplifier will support two other amplifiers with two XC-3 accessories, as shown. The 4th-order Linkwitz-Riley low-pass filters have 24 dB/octave slopes.

Each channel has an all-pass filter providing delay for time alignment. Frequency and delay parameters for both channels are set individually, although typically they would be set the same.

Each channel has a trim control that provides 0 to 20 dB of attenuation for matching levels among the various frequency bands.

SF-3The SF-3 Subwoofer Filter has two summed inputs and a bandpass filter that defines the frequency range of the subwoofer program. The frequencies of the 2nd-order high-pass and 4th-order Linkwitz-Riley low-pass filters are both set by the user by selecting and installing the appropriate SIP networks. The high-pass filter also has a switchable low-frequency boost feature: switched on, it provides a 6 dB bump at the selected high-pass frequency, useful for extending the low-end response of some speaker systems; off, the response is a flat Butterworth curve that is 3 dB down at the selected frequency. The output is parallel, feeding the same signal into both channels of the amplifier. The SF-3 has no delay function. A level trim control provides 0 to 20 dB of attenuation.

The SF-3 can be used to derive subwoofer-range program from full-range audio, as shown, opposite page, bottom-left. It can also be used with a discrete subwoofer channel in cinema sound systems.

4

Image 4 QSC Audio DCA Series user manual Introduction & Description of Each Model, Description of each model
Contents Cinema Accessories Important Safety Information Please Review Explanation of Graphical SymbolsTable of Contents Introduction Introduction & Description of Each ModelDescription of each model Configuring the Accessories Configuring the AccessoriesXC-3 Factory-installed SIPs Setting up the XC-3XC-3 XC-3 Factory Switch Settings XC-3 Recommended Amplifier SettingsSetting Up the LF-3 LF-3LF-3 Factory Switch Settings LF-3 Factory-installed SIPsLF-3 Recommended Amplifier Settings Setting up the SF-3 SF-3SF-3 Factory Switch Settings SF-3 Factory-installed SIPsSF-3 Recommended Amplifier Settings Mounting the Accessories MOUNTING- All ModelsPage Maintenance and Warranty CleaningHOW to Contact QSC World Wide WEB Telephone NumbersPH 714 754-6175 FAX 714