Whirlpool ET16AKXL Adjusting the Shelves and Meat Pan, Reversing the Door Swing, Removing, Shield

Tilt the Front;

Lift the Back

,Push in the Ceder; Pull Down

Push the lab to Clear the Cover

Adjusting the Shelves and Meat Pan.

Arrange your refngerator shelves and meat pan to suit yourself.

You can put two shelves together to make one full-width shelf, or put

them on different levels.

To remove them, tilt up at the front. Then lift up at the back. When

replacing them, keep them tilted; guide the rear hooks into the slots

in the shelf bracket. Lower the front.

Before moving the meat pan itself, remove the pan by pulling it out, lifting the front and then pulling out the rest of the way.

Reversing the Door Swing.

You can change the hinges on your refrigerator so the doors open

the other way. If you rearrange your kitchen or move your refrigera- tor to a new kitchen, you might like your doors to open the other way.

Refer to the enclosed instruction sheet.

Removing

the

light

Shield.

You

may

want

to

remove

the

light

shield

when

cleaning,

or

for

changing

the

bulb.

First,

unplug

the

refrigerator.

Then,

push

lightly

on

the

upper

center

of

the

shield

until

the

notched

tab

is

free

from

the

console.

Pull

down

until

the tab

clears,

then lift

the back

hooks out

of

their

slots.

To

replace

it, do

the reverse.

Removing

the

Crispers

and

Crisper

Covers.

To

remove

the

crispers,

slide

them

out

until

they

stop.

Lift the

front a

little

and

slide

them

the

rest

of

the

way

out.

Each

cover

is

held

in

place

by

two

pegs

at

the

back

and

two

notched

tabs

in

the

front.

Press

the

tabs

out of the

way

to lift

the

front.

Lift the

back

off

the

pegs.

To

put

the

covers

back,

replace

the center

leg.

Replace

each

cover

by

first

fitting

the

back

notches

over

the pegs.

Then

push

the

front

down

into

the

notched

tabs.

The

center

leg

can

be

made

shorter

or

longer

to

help

level

the

crisper

covers,

if

necessary.

Turn the

leg

clockwise

to

make

it

longer.

Turn

it

counter-clockwise

to

shorten

it.

ICE MAGIC”

Automatic

Ice

Maker.

If you

have

the

automattc

Ice

maker

accessory

or plan

to add

one

later

(Part No. ECKMF-6).

there

are a few things you will want to know:

Snap

Back

Into Place

l

The

ON/OFF

lever

is a

wire

signal

arm.

Down...for

making

Ice

automattcally,

Up. .toshut off the Ice maker.

l

Shake

the

bin

occasionally

to

keep

cubes

separated.

and

to

obtain

increased

storage

capacity.

l

It IS normal

for

ice

crescents

to

be attached

by

a corner.

They

will

break

apart

easily.

l

You

will

hear

water

running

when

ice

maker

IS working.

You’ll

hear

ice

fall Into the bin Don’t let these sounds bother you.

l

The

Ice

maker

will

not

operate

until

the freezer

IS cold

enough

to

make

ice. This can take overnight.

l

Because

of

new

plumbing

connections,

the

first

Ice

may

be

discolored

or

off-flavored.

Discard

the

first

few

batches

of

ice.

l

If

ice

is not

being

made

fast

enough

and more

ice

is needed,

turn

the

Temperature

Control

toward

a

higher

number.

Walt

a

day

and,

if

nec-

essary,

turn

the

Air

Control

toward

A.

Raise

Signal

l If you remove the ice bin, raise the signal arm to shut off the ice maker.

When

you return

the

bin,

push

It all

the

way

in and

lower

the

arm

to the

Arm to Stop Ice Maker

ON

position

lower

Signal

l

If

cubes

are

stored

too

long,

they

may

develop

on off-flavor...like

stale

Arm to

Start

II.

water.

Throw

them

away.

They

will

be

replaced.

Cubes

in

the

ice

bin

can

also

become

smaller

by

evaporation