Whirlpool W10162459A, W10162458A Connect Water Supply, Reverse Osmosis Water Supply, Style

Page 4

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ¹⁄₂" (12.70 mm) to 1¹⁄₄" (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1.Unplug refrigerator or disconnect power.

2.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3.Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

A

B

C

D

A. Tube clamp

C. Compression nut

B. Copper tubing

D. Valve inlet

6.The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Refrigerator Safety Refrigerator User InstructionsUnpack the Refrigerator Installation InstructionsBefore You Throw Away Your Old Refrigerator or Freezer LocationRequirements Electrical RequirementsWater Supply Requirements Recommended Grounding MethodReverse Osmosis Water Supply Connect Water SupplyStyle Temperature Control Adjustment and Cooling On/Off Using theControlsRefrigerator USE Adjusting the Controls Condition Temperature AdjustmentAdditional Features Fast Cool & Fast Ice Refrigerator ControlsConvertibleDrawer Temperature Control Crisper Humidity ControlChilled Door Bin Water and Ice DispensersTo Dispense Water Standard To Dispense Water Measured FillIce Maker and Storage Bin To Dispense IceCleaning To Clean Your RefrigeratorRefrigerator Care Water Filtration SystemTroubleshooting Refrigerator OperationMotor seems to run too much Refrigerator is noisyTemperature is too warm Temperature and MoistureIceand Water Accessories Stainless Steel Cleaner and PolishWater dispenser will not operate properly Recently dispensed large amount of water? Allow 24 hoursPerformance Data Sheets Application Guidelines/Water Supply ParametersBase Grille Water Filtration System Limited Warranty Items Excluded from WarrantyThis limited warranty does not cover Disclaimer of Implied Warranties Limitation of RemediesSécurité DU Réfrigérateur RéfrigérateurInstructions Dinstallation Exigences demplacementDéballagedu réfrigérateur Avant de jeter votre vieux réfrigérateur ou congélateurMéthode recommandée de mise à la terre SpécificationsélectriquesSpécifications del’alimentationen eau Alimentation en eau par osmose inverseRaccordement à une canalisation d’eau Raccordement de la canalisation deauRaccordement au réfrigérateur Achever l’installation Utilisation des commandesUtilisation DU Réfrigérateur Condition Ajustement DE LA Température Compartiment fraîcheur dans la porte Commande de température dans Le tiroir convertibleDistributeurs d’eauet de glaçons Distribution deau standard Distribution deau remplissage mesuréLe distributeur deau Unités Par défaut Minimum MaximumMachineà glaçons et bac dentreposage Distribution de glaceEntretien DU Réfrigérateur Système de filtrationde leauNettoyage Nettoyage de votre réfrigérateurDépannage Remplacement des ampoules d’éclairageFonctionnement du réfrigérateur Glaçons et eau Température et humiditéLes portes sont difficiles à ouvrir Nettoyant et poli pour acier inoxydable AccessoiresCartouche du filtre de la base standard Feuilles DE Données SUR LA Performance Système de filtration deau de la grille de la baseSystème de filtration deau de la grille de la base Garantie DES Gros Appareils Ménagers Whirlpool Corporation Garantie LimitéeArticles Exclus DE LA Garantie La présente garantie limitée ne couvre pas

W10162458A, W10162459A specifications

The Whirlpool W10162459A and W10162458A are essential accessories for enhancing kitchen operations, particularly in Whirlpool kitchen appliances. These models cater primarily to the need for improved filtration and performance, ensuring that appliances work efficiently while providing cleaner, healthier results.

One of the standout features of these models is their advanced filtration technology, which effectively removes unwanted contaminants from water. Users can expect a significant reduction in impurities, which contributes to improved taste and quality of water and ice produced by refrigerators. This technology is vital for consumers who are health-conscious and prefer fresh water free from chlorine and other undesirable chemicals.

The W10162459A and W10162458A models are designed for easy installation, ensuring that even those without technical expertise can replace their old filters with these new units. The process is straightforward due to the user-friendly design, which aligns perfectly with Whirlpool appliances, making maintenance a hassle-free experience. This characteristic emphasizes convenience, catering to busy individuals and families who rely on their kitchen appliances for daily functioning.

Durability is another key characteristic of these filters. Constructed with high-quality materials, they are built to last and maintain performance over extended periods. The replaced filters not only promise efficiency but also reduce the frequency of replacements, saving consumers both time and money in the long run.

In terms of compatibility, the W10162459A and W10162458A are designed to fit a range of Whirlpool refrigerator models. This versatility makes them a popular choice among consumers with different appliance models, ensuring that users are not limited by specific models or brands when looking for replacement filters.

Moreover, the filters meet or exceed industry standards for water filtration, instilling confidence in users about the safety and quality of their drinking water. The technology within these models assures users that they are making a smart choice for their health and well-being.

In summary, the Whirlpool W10162459A and W10162458A filters offer a combination of advanced filtration technology, easy installation, durability, compatibility, and adherence to safety standards. These features make them indispensable accessories for anyone looking to enhance their kitchen experience, ensuring that their appliances operate optimally while providing fresh, clean water.
Top Page Image Contents