Whirlpool W10206421B manual Vacationand Moving Care, To shut down the ice maker

Page 13

9.Remove, clean and replace the ice scoop and ice scoop holder.

■After removing the ice scoop, remove the holder by removing the two thumb screws.

■Wash the ice scoop holder along with the other interior components using the following instructions.

■Replace the ice scoop holder by replacing the thumb screws.

A

B

A. Thumb screws

B. Ice scoop holder

10.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

11.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

12.Check the following:

■Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

■Hose from water pan is inserted into storage bin drain opening.

13.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

14.Replace the plastic cutter grid cover and the two screws.

15.Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

16.Plug in ice maker or reconnect power.

17.After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

Vacationand Moving Care

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

8.If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For ice makers with a drain pump installed:

■Plug in ice maker or reconnect power.

■Turn ice maker off and remove all remaining ice from ice bin.

■Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the ice maker stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump.

■Unplug ice maker or disconnect power.

9.Before using again, clean the ice maker and storage bin.

10.Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents W10206421B ICE MakerTable DES Matières Table of ContentsYour safety and the safety of others are very important ICE Maker SafetyCleaning Before Use Installation InstructionsUnpack the IceMaker LocationRequirementsWater Supply Requirements Electrical RequirementsLeveling Recommended grounding methodConnect Water Supply Connecting the Water LineGravity Drain System DrainConnectionRear View Side ViewIce Maker Door Connecting the DrainDrain Pump System on some models Remove doorReplace Door Reverse HingesTop Hinge Bottom HingeNormal Sounds ICE Maker USEHow Your Ice Maker Works Ice Making ProcessCleaning Using the ControlsICE Maker Care Interior Components CondenserDirty or clogged condenser Vacationand Moving Care For ice makers with a drain pump installedTo shut down the ice maker Ice Maker Operation TroubleshootingIce Production Plumbing Problems Assistance or ServiceIce Quality U.S.AItems Excluded from Warranty Limited WarrantyThis limited warranty does not cover Disclaimer of Implied Warranties Limitation of RemediesVotre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsExigences demplacement Instructions D’INSTALLATIONDéballage de la machine à glaçons Enlèvement des matériaux d’emballageSpécificationsélectriques Méthode de mise à la terre recommandéeSpécifications del’alimentationen eau NivellementRaccordement du tuyau d’eau Raccordement à la canalisation d’eauVidange par gravité Raccordementau drain de vidangeVUE Arrière VUE LatéraleSystème avec pompe de vidange sur certains modèles Porte de la machine à glaçonsRaccordement du drain de vidange Dépose de la porteInversion des charnières Inversion du loquet de porte Réinstallation de la porteCharnière supérieure Charnière inférieureSonsnormaux GlaçonsFonctionnement dela machine à glaçons Fabrication de la glaceNettoyage Utilisation des commandesUn condenseur sale ou bouché CondenseurComposants intérieurs Arrêt de la machine à glaçons DéménagementMachine à glaçons avec pompe de vidange Fonctionnement de la machine à glaçons DépannageProductionde glaçons La machine à glaçons ne fonctionne pasQualité des glaçons Assistance OU ServiceProblèmes de plomberie Garantie Limitée Garantie DES Gros Appareils Ménagers Whirlpool CorporationArticles Exclus DE LA Garantie La présente garantie limitée ne couvre pasWhirlpool Corporation All rights reserved W10206421B

W10206421B specifications

The Whirlpool W10206421B is a versatile, high-quality refrigerator that seamlessly combines innovation with efficiency, making it an excellent choice for modern kitchens. One of the standout features of this appliance is its spacious interior, designed to offer ample storage for groceries and food items. The refrigerator is crafted with adjustable shelves, allowing users the flexibility to customize the space according to their needs. This adaptability is particularly beneficial for accommodating larger items, such as cakes or party platters.

In terms of cooling technology, the Whirlpool W10206421B employs a powerful refrigeration system that ensures consistent and optimal temperatures throughout its compartments. The refrigerator is equipped with a multi-airflow system, which circulates cool air evenly. This feature helps to preserve food freshness and prevents hot spots, ensuring that all items remain at an ideal temperature, thus reducing spoilage.

Energy efficiency is another hallmark of the W10206421B. It is designed with energy-saving features that not only help in reducing electricity bills but also minimize environmental impact. The Energy Star certification signifies that this refrigerator meets strict energy efficiency guidelines, making it a smart choice for eco-conscious consumers.

This model also boasts a sophisticated water filtration system, providing clean and tasty water and ice. The built-in water dispenser is convenient and user-friendly, ensuring you have access to fresh drinking water at all times. In addition, the ice maker feature ensures that you always have ice on hand without the need for ice trays.

Furthermore, the Whirlpool W10206421B comes with a sleek design that enhances its aesthetic appeal. The stainless steel finish adds a modern touch to any kitchen decor, while the easy-to-clean surfaces make maintenance a breeze.

Additional features include LED lighting, which illuminates the interior effectively, and door bins that provide extra storage options for smaller items. Overall, the Whirlpool W10206421B is designed with user convenience, energy efficiency, and food preservation in mind, making it a reliable appliance for families and individuals alike.
Top Page Image Contents