Whirlpool W10206421B manual Connect Water Supply, Connecting the Water Line

Page 6

3.Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the ice maker.

4.Using an adjustable wrench, change the height of the legs as follows:

■Turn the leveling leg to the right to lower that side of the ice maker.

■Turn the leveling leg to the left to raise that side of the ice maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

5.Push up on the top rear of the ice maker and locate the leveling legs that are on the bottom rear of the ice maker.

6.Follow the instructions in Step 4 to change the height of the legs.

7.Use the level to recheck the ice maker to see that it is even from front to back and side to side. If the ice maker is not level, repeat steps 2 to 5. If the ice maker is level, go to the “Connect Water Supply” section.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.

■Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks.

■Install tubing only in areas where temperatures will remain above freezing.

Tools needed:

Gather the required tools and parts before starting installation.

■Flat-blade screwdriver

■⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■¹⁄₄" nut driver

NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Connecting the Water Line

1.Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

2.Using a ¹⁄₂" copper supply line with a quarter-turn shutoff valve or the equivalent, connect the ice maker as shown.

NOTE: To allow sufficient water flow to the ice maker a minimum ¹⁄₂" size copper supply line is recommended.

A

B

A.Bulb

B.Nut

3.Now you are ready to connect the copper tubing. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply.

■Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A B

C

A. Compression sleeve

C. Copper tubing

B. Compression nut

 

4.Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

5.Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents ICE Maker W10206421BTable of Contents Table DES MatièresICE Maker Safety Your safety and the safety of others are very importantUnpack the IceMaker Installation InstructionsCleaning Before Use LocationRequirementsLeveling Electrical RequirementsWater Supply Requirements Recommended grounding methodConnecting the Water Line Connect Water SupplyRear View DrainConnectionGravity Drain System Side ViewDrain Pump System on some models Connecting the DrainIce Maker Door Remove doorTop Hinge Reverse HingesReplace Door Bottom HingeHow Your Ice Maker Works ICE Maker USENormal Sounds Ice Making ProcessUsing the Controls CleaningICE Maker Care Condenser Interior ComponentsDirty or clogged condenser For ice makers with a drain pump installed Vacationand Moving CareTo shut down the ice maker Troubleshooting Ice Maker OperationIce Production Ice Quality Assistance or ServicePlumbing Problems U.S.AThis limited warranty does not cover Limited WarrantyItems Excluded from Warranty Disclaimer of Implied Warranties Limitation of RemediesSécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteDéballage de la machine à glaçons Instructions D’INSTALLATIONExigences demplacement Enlèvement des matériaux d’emballageSpécifications del’alimentationen eau Méthode de mise à la terre recommandéeSpécificationsélectriques NivellementRaccordement à la canalisation d’eau Raccordement du tuyau d’eauVUE Arrière Raccordementau drain de vidangeVidange par gravité VUE LatéraleRaccordement du drain de vidange Porte de la machine à glaçonsSystème avec pompe de vidange sur certains modèles Dépose de la porteCharnière supérieure Réinstallation de la porteInversion des charnières Inversion du loquet de porte Charnière inférieureFonctionnement dela machine à glaçons GlaçonsSonsnormaux Fabrication de la glaceUtilisation des commandes NettoyageCondenseur Un condenseur sale ou bouchéComposants intérieurs Déménagement Arrêt de la machine à glaçonsMachine à glaçons avec pompe de vidange Productionde glaçons DépannageFonctionnement de la machine à glaçons La machine à glaçons ne fonctionne pasAssistance OU Service Qualité des glaçonsProblèmes de plomberie Articles Exclus DE LA Garantie Garantie DES Gros Appareils Ménagers Whirlpool CorporationGarantie Limitée La présente garantie limitée ne couvre pasW10206421B Whirlpool Corporation All rights reserved

W10206421B specifications

The Whirlpool W10206421B is a versatile, high-quality refrigerator that seamlessly combines innovation with efficiency, making it an excellent choice for modern kitchens. One of the standout features of this appliance is its spacious interior, designed to offer ample storage for groceries and food items. The refrigerator is crafted with adjustable shelves, allowing users the flexibility to customize the space according to their needs. This adaptability is particularly beneficial for accommodating larger items, such as cakes or party platters.

In terms of cooling technology, the Whirlpool W10206421B employs a powerful refrigeration system that ensures consistent and optimal temperatures throughout its compartments. The refrigerator is equipped with a multi-airflow system, which circulates cool air evenly. This feature helps to preserve food freshness and prevents hot spots, ensuring that all items remain at an ideal temperature, thus reducing spoilage.

Energy efficiency is another hallmark of the W10206421B. It is designed with energy-saving features that not only help in reducing electricity bills but also minimize environmental impact. The Energy Star certification signifies that this refrigerator meets strict energy efficiency guidelines, making it a smart choice for eco-conscious consumers.

This model also boasts a sophisticated water filtration system, providing clean and tasty water and ice. The built-in water dispenser is convenient and user-friendly, ensuring you have access to fresh drinking water at all times. In addition, the ice maker feature ensures that you always have ice on hand without the need for ice trays.

Furthermore, the Whirlpool W10206421B comes with a sleek design that enhances its aesthetic appeal. The stainless steel finish adds a modern touch to any kitchen decor, while the easy-to-clean surfaces make maintenance a breeze.

Additional features include LED lighting, which illuminates the interior effectively, and door bins that provide extra storage options for smaller items. Overall, the Whirlpool W10206421B is designed with user convenience, energy efficiency, and food preservation in mind, making it a reliable appliance for families and individuals alike.
Top Page Image Contents