Water Requirements, Drain Requfrements | Whirlpool 3369092 REV. A

Water

Requirements

The hot water line to the dishwasher must provide between 15 - 120 psi water pressure. The hot water heater should be set to deliver 140°F water temperature to the dishwasher for best results.

Use 3/8” O.D. copper tubing or l/2” plastic tubing minimum inlet line. Dishwasher inlet valve has 3/8” N.P.T. internal pipe thread

Drain

Requfrements

The drain hose MUST have a high drain loop, 20” minimum ABOVE FLOOR, to prevent backflow or water siphoning out of dishwasher during operation.

NOTE:An air gap MUSTBEUSEDin the high drain loop if the drain hose is connected to house plumbing lower than 20” above the floor.

Drain hose, supplied, meets AHAM DW- 1 test standards. Cut l-1/2” hole in cabinet wall for drain hose. Additional drain line (a minimum of l/2” I.D. and no longer than 20’) can be used if needed.

Now start...

with dishwasher in kitchen.

alternate water- line locations

1n Rough in water line to the dish- washer cabinet opening using one of the routing methods shown. Cut l/2” or larger hole in cabinet wall for water line.

2n Install a shutoff valve in the water line where it can be easily used.

3 n Flush water line into a bucket to get rid of any particles that may clog inlet valve. Turn shutoff valve to the “OFF”position.

Electrical Shock Hazard

Disconnect electrical power at the service panel (fuse box or circuit breaker box).

Failure to do so could result in serious injury or death.

I-----r

electrical

2-l/2”

4 l Cut a 1-l/2” maximum hole for power supply cord or a 3/4” minimum hole for direct wiring in the cabinet or floor for the electrical wiring to pass through. If this hole is cut in a wood cabinet, sand the hole until it is smooth. If the hole is cut in a metal cabinet, the hole must be covered by a grommet (Part No. 3027971, available from your dealer or parts supplier.

Install wall receptacle on rear or side wall of a cabinet next to dishwasher opening as indicated by the shaded areas shown. Plug dishwasher power supply cord into this receptacle.

For direct wiring install a 3/4” U. L.-listed conduit connector to connect the flexible armored or non-metallic sheathed, copper cable (with grounding wire> to the fused disconnect, circuit breaker or junction box. Run the cable through the hole in the cabinet opening. The cable should extend 24” from the back wall.

ove 4 screws.

5 n Remove the 4 screws attaching access panel and toe panel to dishwasher using a l/4” hex socket, nut driver or Phillips screwdriver. Remove access panel and toe panel.

6 n The dishwasher is shipped to be installed in cabinet opening with a 34” height. Measure height of cabinet opening from the front edge of the underside of cabinet opening to floor. Check chart for that height opening. Put the wheels in the required position. The dishwasher should be installed as level as possible from front to back.

Loosen and then turn front levelers the number of times indicated in the chart.

Min.	Wheel	Number
Min.	Position	Of	Turns
cutout	(See	To	Adjust
Height	Illustration)	Levelers
33-710”	1		0
34-1116”	2		3
34-114”	3		6
34-7116”	4		9
For additional	height:

I. Add shims under the wheels.

2.Turn front levelers (each turn adds l/16” in height).

You may have this type drain

connector...

7w Put spring-type drain hose clamp over connector. Push drain hose onto connector. Use pliers to open clamp and slide clamp over drain hose and connector. Check that drain hose is secure.

If screw-type clamp is supplied instead of spring-type clamp, use a 5/l 6” nut driver to tighten drain hose securely to connector.

Panel B

3369092 REV. A specifications

The Whirlpool 3369092 REV. A is a versatile and innovative appliance that enhances the functionality of a kitchen while showcasing modern engineering prowess. Designed primarily as a replacement part for various Whirlpool refrigerators, this component delivers reliability and efficiency, ensuring optimal performance in food storage.

One of the main features of the Whirlpool 3369092 REV. A is its robust construction, which is made to withstand the rigors of daily use. The component is crafted from high-quality materials, making it durable and resistant to wear and tear. This durability is crucial for maintaining long-term performance in busy household environments.

In terms of technology, the Whirlpool 3369092 REV. A incorporates advancements that cater to energy efficiency. Efficient appliances are a priority for modern consumers, and this component plays a role in reducing energy consumption, which can lead to substantial savings on utility bills. By optimizing the refrigerator’s operation, this part ensures that food stays fresh without consuming excessive power.

Moreover, the design of the Whirlpool 3369092 REV. A emphasizes ease of installation. The part is engineered to fit seamlessly into compatible refrigerator models, making it a straightforward task for users to replace worn-out components. This user-friendly approach is especially valuable for those who may not have extensive technical knowledge, as it allows for quick repairs without professional help.

Another characteristic to highlight is the adaptability of the Whirlpool 3369092 REV. A. It is designed to work with a variety of Whirlpool refrigerator models, making it a versatile choice for maintenance. This adaptability ensures that consumers can find a reliable replacement without needing to worry about compatibility issues.

In conclusion, the Whirlpool 3369092 REV. A stands out as a significant component that enhances refrigerator performance through its durable construction, energy efficiency, user-friendly installation, and broad compatibility with various models. For anyone looking to maintain their Whirlpool refrigerator, investing in this component is a smart decision that promises to extend the life of their appliance while ensuring optimal functionality. It is a testament to Whirlpool's commitment to quality and innovation in the home appliance sector.