Whirlpool 9.76E+13 installation instructions Direct wire method Copper or Aluminum wire

Page 7

Direct wire method: Copper or Aluminum wire

NOTE: The bag containing three aluminum terminal lugs must be used when making a direct wire connection.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire, or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death, fire, or electrical shock.

This range may be connected directly to the fuse disconnect or circuit breaker box; or with a U.L.-listed, 40 amp range power supply cable. Depending on your electrical supply, make the required three-wire or four-wire connection.

1.Disconnect power.

2.Remove the knockout as needed for conduit connection.

3. Assemble a

U.L.-listed

conduit

U.L.-listed

connector in

conduit

opening.

connector

 

4.Strip outer covering back 3 inches to expose wires. Strip the insulation

back 1 inch from the end of each wire.

3"

1"

5.Allow enough slack in the wire to easily attach the wiring terminal block.

6.Use 3/8" nut driver and remove the outside nuts on the terminal block screws. Do not loosen the factory- tightened nuts behind the outside nuts.

7.IMPORTANT: the aluminum terminal lugs must be assembled to the terminal posts with the set screws facing out as shown.

8.Attach three aluminum terminal lugs to terminal posts.

Use a 3/8" nut driver and tighten the nuts securely. Nuts must be tightened to 20 in/lbs of torque for proper electrical connection.

9.Complete electrical connection according to your type electrical supply (“Four-wire electrical connection” or “Three-wire electrical connection.”)

Four-wire electrical connection:

ground

link

ground screw

Figure 1

slotted set screw

line 1

neutral

(center wire)

green

groundline 2 wire

Figure 2

Use this method for new installations, mobile homes, recreational vehicles and whenever four-wire installation is required.

10.Remove the ground-link screw from the range frame. Save the ground-link screw and cup washer. Bend up the ground link so that it does not contact the range. See Figures 1 and 2.

11.Connect the green ground wire to the range using the ground-link screw and cup washer. The ground wire must be attached first and must not contact any other terminal. See Figure 2.

12.Loosen (do not remove) the 3 slotted set screws. Insert the neutral (white) wire into the hole at the bottom of the center position lug (attached to center terminal screw black terminal block). See Figure 2.

13.Connect the other two wires (lines 1 and 2) to the outer aluminum lugs.

14.Securely tighten the set screws. For 8 gauge copper wire, tighten to 25 in/lbs of torque, and for 6 gauge aluminum wire, tighten to 35 in/lbs of torque to make a proper electrical connection. See Figure 2.

15.Tighten the locking ring of the conduit connector.

16.Replace the terminal block cover.

Three-wire electrical connection:

slotted

set screw

 

neutral

line 1

(center wire)

line 2

Figure 3

Use this method only if local codes permit connecting ground conductor to neutral supply wire.

10.Loosen (do not remove) the 3 slotted set screws. Insert the neutral (white) wire into the hole at the bottom of the center position lug (attached to center terminal screw of terminal block). See Figure 3.

11.Connect the other two wires (lines 1 and 2) to the outer aluminum lugs.

12.Securely tighten the set screws. For 8 gauge copper wire, tighten to 25 in/lbs of torque, and for 6 gauge aluminum wire, tighten to 35 in/lbs of torque to make a proper electrical connection. See Figure 3.

13.Tighten the locking ring of the conduit connector.

14.Replace the terminal block cover.

aluminum lug

terminal screw

set screw must face out

7

Image 7
Contents Table of Contents Installation InstructionsParts supplied Mobile home installationBefore you start Tools neededCabinet dimensions/requirements Product dimensionsRecommended ground method If connecting to a four-wire systemIf connecting to a three-wire system Electrical requirementsElectrical connection Now startFour-wire electrical connection Power supply cord methodThree-wire electrical connection Direct wire method Copper or Aluminum wire Operating position MED Check operationMoving the range If you need serviceIf range does not operate If you need assistance

9.76E+13 specifications

Whirlpool 9.76E+13 is a dishwasher model that embodies the brand's commitment to innovation and consumer satisfaction. This advanced appliance is designed to streamline the dishwashing process, making it a valuable addition to any kitchen.

One of the standout features of the Whirlpool 9.76E+13 is its impressive capacity. With the ability to accommodate up to 15 place settings, it is perfectly suited for both small families and larger gatherings. The flexible loading options, including adjustable tines and a third rack, allow users to customize the interior space to fit various dish sizes and shapes. This ensures that every item, from pots to delicate glassware, can be cleaned efficiently.

Energy efficiency is another hallmark of the Whirlpool 9.76E+13. Rated highly in energy performance, the dishwasher uses cutting-edge technologies to minimize water and energy consumption without compromising on cleaning power. The Eco Wash cycle is particularly noteworthy, as it uses less water and energy while still delivering exceptional cleaning results. This feature is not only environmentally friendly but also cost-effective for the user.

The integration of advanced washing technologies, such as the Sensor Cycle, further elevates the performance of this dishwasher. This intelligent system automatically detects soil levels and adjusts the wash cycle for optimal cleaning. Additionally, the Precision Clean feature utilizes high-pressure jets to ensure that even the toughest stains and food residues are effectively removed, resulting in sparkling clean dishes every time.

Noise levels are a common concern among dishwasher users, and Whirlpool addresses this with the Whisper Quiet technology. Operating at a mere 47 decibels, the dishwasher runs quietly, making it easy to use even during late-night hours or while entertaining guests.

Convenience and user-friendliness are also prominent in the Whirlpool 9.76E+13. The intuitive control panel features easy-to-understand buttons and settings, while the Delay Start option allows users to set the dishwasher to run at a more convenient time. Interior LED lighting enhances visibility, making sure that loading and unloading is an effortless task.

In summary, the Whirlpool 9.76E+13 is a sophisticated dishwasher that combines efficiency, advanced technology, and user-friendly features. Its capacity, energy-saving capabilities, and quiet operation make it an excellent choice for households seeking a reliable and modern kitchen appliance. Whether you are washing everyday dishes or hosting a special event, this dishwasher stands ready to deliver outstanding results.