Cannon C50GKX, C50GKW, C50GKB, C50GKS manual Gas connection, Connecting the gas supply

Page 5

Gas connection

The cooker should be connected to the gas-supply by a corgi registered installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed “Adaptation to different gas types”. In the case of connection to liquid gas, by tank, use pressure regulators that conform to the regulation in force. The gas supply must be connected to the left of the appliance. Be sure that the hose does not pass through the rear of the cooker touching hot parts.

HOT PARTS

600 mm

Important: make sure the supply pressure conforms with the values shown in the table entitled “Caracteristics of the burners and nozzles”. When the cooker is installed between cabinets (recessed), the gas connection must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition).The gas inlet for the cookers is a threaded G 1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:

•the hose must never be at any point in its lenght in contact with the “hot” parts of the cooker;

•the hose must never be longer than 1,5 metre;

•the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow curves or bottlenecks;

•the hose must be easy to inspect along its entire length to check its condition;

•the hose must always be in good condition, never attempt to repair.

Important: the installation must comply with gas safety (installation and use) regulations 1984. In all cases for the above, by low, a qualified, corgi approved engineer must be called for installation.

Important: Before using the main/top oven, position the oven burner deflector "A" (provided with the appliance) in the correct place by inserting the lower tab into the support slot (see figure).

A

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Kitchen think Contents Introduction Installation of the cooker InstallationGas connection Connecting the gas supplyAdapting to different types of gas main and top oven Disposing of the applianceAdapting the cooker to different types of gas Adapting the gas grill to different types of gas Electrial connection Liquid Gas Natural Gas Burner and Nozzle SpecificationsAlways Safety InformationExtinguisher is likely to tip the pan over Safety Information NeverSafety Advice in Case of a CHIP-PAN Fire Features Only available on certain models Control PanelControl Knobs for the gas burners HOW to Deal with a FAT Fire Practical Advice on Using the BurnersUse of Hotplates Gas Cut OffRelighting the Burner USE of GrillTo USE the TOP Oven Upper Oven Setting Temperature CGuidance on Using the TOP Oven TOP Oven Cooking Chart Yeast Mixtures Dishes ‘COOK CHILL’Soft Margarine Main Oven Cooking ChartUsing the Main Oven for Other Functions Care and Cleaning Oven Baking Problem Check GrillingCooking Results Not Satisfactory? Something Wrong with your Cooker? Problem CheckMain Oven Technical CharacteristicsTop Oven Voltage and FrequencyTo set the clock To set the timer Electronic timerTo cancel a Previous settingPage Key Contacts

C50GKB, C50GKX, C50GKW, C50GKS specifications

The Cannon C50 series, specifically the C50GKS, C50GKW, C50GKX, and C50GKB models, represents a significant advancement in the realm of modern firearms. Renowned for their reliability, precision, and ergonomic design, these rifles are tailored to meet the needs of both amateur and professional shooters alike.

One of the standout features of these models is their advanced gas-operated reloading system, which ensures swift and seamless operation, allowing for consistent firing even during prolonged use. This gas system not only contributes to the rifles' impressive rate of fire but also minimizes recoil, enhancing the shooter's control and accuracy. Each model in the C50 series is engineered for optimal performance, making them suitable for various shooting applications from competitive sports to tactical scenarios.

In terms of construction, the C50 series incorporates high-quality materials that enhance durability and resistance to wear and tear. The barrels are crafted from premium steel, ensuring longevity while maintaining accuracy. Additionally, these rifles feature a modular design that allows for easy customization. Shooters can modify components such as sights, grips, and stocks according to personal preferences, making each rifle truly unique.

The user-friendly design extends to the controls of the C50 models, which have been thoughtfully placed for ease of access. Shooters will appreciate the ambidextrous safety mechanism and magazine release, allowing for a comfortable experience regardless of their dominant hand. The adjustable stock included in these models caters to different shooter heights and preferences, ensuring a perfect fit for maximum comfort.

Technology plays a crucial role in the C50 series, with some models featuring integrated optics ready mounts that facilitate the addition of red dot sights or scopes. This not only enhances targeting accuracy but also allows shooters to quickly acquire targets under a variety of conditions.

In summary, the Cannon C50GKS, C50GKW, C50GKX, and C50GKB rifles are exceptional firearms that combine innovation with practicality. Their advanced technology, robust construction, and customizable options make them a top choice for those seeking reliability and performance in a firearm. Whether for sport shooting, hunting, or tactical use, these models promise to deliver an unparalleled shooting experience.
Top Page Image Contents