Clarion PSWFRGR manual Preparation, Overview, Procedure

Page 1

PREPARATION

Parts list

(Qty) Component

Preassembled

Loose Components

(1)

Roto-molded subwoofer enclosure

(1) 17’ wire harness w/ pigtail style connector

(1)

8"; 2 ohm subwoofer

(2) Attachment brackets

(1)

100W class "D" amplifier

(4)

3/4" pilot point wafer Phillips head screws

(1)

Speaker grille

(4)

1" self taping wafer Phillips head screws

 

 

(1) 1/2" ground screw

 

 

(1) Star washer

WIRING:

Note: Installer MUST disconnect speaker-input leads to amplifier when using line-level input

OVERVIEW

The Clarion Camouflage subwoofer system provides for the installation of a low frequency driver in an enclosure which is powered by a small low current, high power class "D" (Digital) amplifier. The advantage to using this type of amplifier is in the low current consumption of the amplifier at high power levels. The class "D" amplifier provided with this system will produce a rated 100W into a 2 ohm load. The woofer supplied with this system uses a voice coil with rated imped- ance of 2 ohms, and therefore is not considered a standard woofer. Replacing the woofer with any driver having an impedance greater than 2 ohms will yield lower power output from the amplifier, and is not recommended.

PROCEDURE

Proper installation of this product requires proper tools and knowledge of car audio principles. If you are not comfortable performing any of the outlined tasks below, contact a professional installation facility to perform the work.

OUTLINE

Remove the head unit.

Connect the Clarion "T" harness between the radio and factory wiring and route the harness extension to transmis- sion hump of the vehicle.

Install subwoofer enclosure.

Test subwoofer enclosure and head unit functions (fade, balance, dim, etc.).

Adjust subwoofer gain.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CON- DITIONS.

(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDE- SIRED OPERATION.

1

Image 1
Contents Preparation ProcedureOverview Qty Component Preassembled Loose ComponentsRemove the Radio Step Connect the T Harness Remove the Radio Step Connect the wiresTest and SET the Gain III. Install the Brackets to the Enclosure II. RUN Wire HarnessIV. Test the Enclosure VI. Reassemble the Vehicle Attach the Enclosure to Vehicle

PSWFRGR specifications

The Clarion PSWFRGR is an innovative product that stands out in the realm of car audio systems, combining exceptional sound quality with user-friendly design. As a component of Clarion's driving-focused audio solutions, the PSWFRGR addresses the needs of discerning audiophiles and casual listeners alike, amplifying their in-car audio experience.

One of the key features of the PSWFRGR is its powerful amplifier that delivers a remarkable output, ensuring that sound is both clear and impactful. With advanced circuitry, this amplifier supports a full range of frequencies, resulting in a well-rounded audio profile. The added bass boost functionality allows for deeper low-end sounds, enhancing the overall listening experience, especially for genres like hip-hop and electronic music.

The system boasts a robust user interface that caters to both tech-savvy users and those seeking simplicity. It is equipped with a digital signal processor (DSP), providing users with customizable sound settings, allowing them to tweak the audio output according to their preferences. With multiple equalizer settings and sound profiles, listeners can easily adjust their audio experience for different types of music or listening environments.

Connectivity is another highlight of the PSWFRGR. It supports Bluetooth, enabling wireless streaming from compatible devices. The seamless integration with smartphones allows users to enjoy their favorite playlists and podcasts without tangled wires. Additionally, USB ports facilitate direct media playback, further enhancing convenience for users.

Moreover, the Clarion PSWFRGR is built with durability in mind. Its sleek, compact design ensures it fits well within various car interiors while maintaining a stylish appearance. The materials used are designed to withstand the rigors of daily use, making it a reliable choice for any car owner.

The unit also features advanced safety protocols. With overcurrent protection and thermal management systems, users can trust that their audio system will function optimally without risk of damage from overheating or power surges. The efficiency of the PSWFRGR guarantees minimal battery drain, preserving the vehicle's power system.

In conclusion, the Clarion PSWFRGR is a comprehensive audio solution combining innovative technology and superior sound performance. Its features, user-friendly design, and durability make it an ideal choice for anyone looking to elevate their driving experience through high-quality audio. Whether for everyday commutes or long road trips, the PSWFRGR stands out as a top-tier choice in the competitive car audio landscape.