Zephyr ZVO-M90AG, ZVO-E30AG manual Hood, FIG. a

Page 11

!

CAUTION: At least two installers are

 

 

Hood

required due to the weight and size of the

 

 

 

hood.

 

 

 

1.

Measure from range top to hood bottom and mark line A. (26”

 

 

 

 

minimum from range top) .

 

 

the

2.

Plum and mark center line.

11 1/4”

 

 

 

3.

Mark mounting height line B. (18 5/8” from line A)

 

 

Mounting

4.

Mark mounting spread from C/L. (11 1/4”)

 

 

5.

shown in (FIG. B #3) and secure to motor housing using the (2)

 

 

Fasten (2) M6 x 1-1/2” screws into studs on line B but do not

 

 

 

 

tighten all the way. Note: Wood blocking may need to be

 

18 5/8”

 

 

added behind the drywall if no studs are present. Wall

 

 

 

 

anchors may also be used but check local codes before

 

 

 

 

using wall anchors.

 

 

 

6.

Remove tape and (2) screws securing electronics mounting

 

 

 

 

bracket to hood. Reposition electronics mounting bracket as

 

26” min

 

 

previously removed screws.

 

 

7.

Remove (2) screws securing electrical junction box to

 

 

 

 

Installation

 

duct tape. Re-install electrical junction box with cable lock and

 

 

 

electronics mounting plate. Remove junction box. (FIG. B #1)

 

 

 

8.

Remove the (2) aluminum mesh fi lters.

Brackets are

 

 

9.

Hang hood onto the mounting screws and hand tighten each

pre-installed

 

 

 

screw. (FIG. A #1) Secure third M6 x 1-1/2” screw through inside

 

 

 

of hood into wall for extra support. (FIG. A #2)

 

1

 

10.

Center and attach duct cover mounting bracket to wall just

 

 

 

 

 

 

below the ceiling or soffi t using (2) M6 x 1” screws.

 

 

 

11.

Install electrical and duct work. Seal duct work with aluminum

 

 

 

 

install the electrical. (FIG. B #2)

 

 

 

12. Power up hood and check for leaks around duct tape.

 

 

 

13.

Place telescopic duct covers onto hood and extend inner (top)

 

2

 

 

duct cover upwards and secure to duct cover bracket using (2)

 

 

 

 

M3.5 x 8 screws.

 

 

 

14. Re-install aluminum mesh fi lters.

*If using hood in recirculating mode you must secure the air diverter plate onto wall before installing duct work and duct covers. Turn to page 10 for more details.

! WARNING: Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring.

Cable Lock

A cable locking connector (not supplied) might be required by local codes. Check with local requirements and codes, purchase and install appropriate connector if necessary.

FIG. A

2

1

Cable Lock

3

Motor Housing

FIG. B

9

Image 11
Contents Use, Care, and Installation Guide Page Installation Table of ContentsRead and Save These Instructions Important Safety NoticeOperation Models ZVO-E30AG & ZVO-M90AG List of MaterialsDuct pieces Equivalent number Total Length x used Installation Ducting Calculation SheetDucting Installation Mounting Height & ClearanceSome Ducting Options OptionsSpecifications Installation HoodFIG. a HoodHood Model Qty to Order Installation Ductless RecirculatingRecirculating KIT Required if no Ducting is Used Hood Model Filters in PkgFeatures & Controls Touch Controls Mesh Filter Clean Indicator always enabled Features & Controls User InterfaceRemoving Aluminum Mesh Filters Maintenance Hood and Filter CleaningSurface Maintenance Aluminum Mesh FiltersIssue Cause What to do TroubleshootingTroubleshooting Procedures for Verona Blower fan curve AC input 120V 60Hz Outlet diameter Wiring & Fan Curve DiagramsDescription PART# List of Parts & AccessoriesReplacement Parts Optional AccessoriesLimited Warranty MAY11.0201 Zephyr Corporation Page Table des matières Lisez ET Conservez CES Instructions Mise en garde de sécuritéFonctionnement Modèles ZVO-E30AG & ZVO-M90AG Liste du matérielDuct pieces Equivalent number Total Length x used Installation Feuille de calcul pour le conduit d’aérationConduit D’AÉRATION Installation Espace libre et hauteur de montageAvertissement DE Risque D’INCENDIE Installation Options pour leConduit d’aération 18 1/8 23 3/16 29 15/16, 35 7/16 22 1/16 InstallationMontage HotteModèle de hotte Numéro de pièce Filtres par paquet Modèle de hotte Numéro de pi Quantité à commander’air sans conduit Fonction d’arrêt automatique CommandesCommandes Interface utilisateur Filtre à tamis en aluminium Modèle de hotte Numéro de pièce Quantité à commanderEntretien Entretien DES SurfacesProcédures DE Dépannage Pour LA Hotte Verona Problème Cause SolutionDépannage Protégé Thermiquement Schéma de câblageNo DE Pièce Des accessoiresListes des pièces et DescriptionGarantie limitée

ZVO-E30AG, ZVO-M90AG specifications

The Zephyr ZVO-M90AG and ZVO-E30AG are remarkable additions to the versatile lineup of Zephyr, a brand known for blending innovation with practicality. These models stand out for their advanced features, robust technologies, and user-centric characteristics that cater to a diverse range of applications.

The Zephyr ZVO-M90AG is a powerful and compact model that excels in performance and efficiency. Its design integrates an advanced motor technology that ensures lower energy consumption while delivering high output power. The prominent features include a user-friendly control panel with intuitive buttons that allow quick adjustments to settings. The adjustable speed settings offer flexibility to tackle various tasks, from gentle to heavy-duty applications.

A key highlight of the ZVO-M90AG is its noise reduction technology, which minimizes operational sound levels. This makes it a suitable choice for noise-sensitive environments, enhancing user comfort. Additionally, the model is equipped with a robust thermal protection system that automatically shuts down the device in case of overheating, ensuring safety and longevity.

On the other hand, the Zephyr ZVO-E30AG showcases a perfect blend of style and functionality. This model distinguishes itself with a sleek, modern design that seamlessly fits into contemporary spaces. Its features include an efficient filtration system that maximizes air purification, making it ideal for maintaining indoor air quality.

The ZVO-E30AG also boasts smart technology integration, allowing users to monitor and control the device remotely via a dedicated app. This feature not only adds convenience but also enhances energy efficiency by enabling users to operate the model according to their schedules. Furthermore, the advanced sensor technology provides real-time feedback on air quality, automatically adjusting settings to optimize performance.

Both models are designed with durability in mind, constructed from high-quality materials that ensure they withstand rigorous use. Easy maintenance is another characteristic that users appreciate; both products feature accessible parts, making cleaning and replacement hassle-free.

In summary, the Zephyr ZVO-M90AG and ZVO-E30AG models exemplify cutting-edge design and engineering. With their array of features, from energy efficiency to smart technology integration, they stand out as top choices for consumers seeking reliability and advanced performance in their appliances. Whether for home or commercial use, they provide solutions that meet modern demands while ensuring ease of use and safety.