SWR Sound 2X10C owner manual Effects Blend Control, Variable Limiter Control with defeat option

Page 8

EFFECTS BLEND CONTROL

The Effects Blend Control "blends" the signal sent from your instrument with the signal coming from an outboard effects unit of your choice. With the Effects Blend fully counter-clockwise ("DRY"), no signal from your outboard effects unit will be heard. As you turn this control clockwise, more of the effect can be heard in the overall sound. When the Effects Blend control is set fully clockwise ("WET"), no true or unaffected signal is heard other than what your outboard effects unit provides. If your outboard effects unit has a similar control, adjust it to the fully clockwise ("WET") position. This will avoid any possible phasing problems.

The Effects Blend circuit is similar to that used on recording consoles with the effects loop on a "side chain" to the normal circuit. Unless the control is set to the full "wet" position, you will always get the full sound of your instrument AND get the diversity an effects unit offers. This circuit is also effective in reducing noise generated by effects units because it is located after the gain stages in the preamp.

The Effects Blend control functions only when the Effects Loop is being used. It is activated when a 1/4" phone plug is inserted into the Effects Receive jack (for more information, please see the heading titled "Effects Loop" in the "Rear Panel Features" section later in this manual).

VARIABLE LIMITER CONTROL (with defeat option)

The Limiter in the Workingman's 2x10C is designed to provide the user with maximum flexibility of control, while at the same time provide protection for the power amplifier from clipping, a condition that can cause damage to itself and the speaker system over time if allowed to occur.

The Limiter circuit is located after (post) the Master Volume and before (pre) the power amplifier, so the Limiter itself is driven by the Master Volume control. You can set the threshold of the Limiter with the Limiter Control. Turning the control clockwise sets the threshold to increase the amount of limiting, while turning the control counter-clockwise will decrease the amount of limiting. As always, your ears will help you determine the right amount of limiting to use, as levels vary greatly from player to player due to play- ing style, output levels of basses, EQ settings, and many other factors. This feature can also be helpful in preventing speaker damage when running your system at high volumes.

NOTE: When listening to hear if there is distortion present in your signal, make sure you are not confusing power amp distortion with preamp distortion. To make sure preamp distortion is not present, be sure to set the Gain Control to where the Preamp Clip LED is not illuminating. Then you can make a clear determination as to how best to set the Limiter.

DEFEATING THE LIMITER CIRCUIT

Regardless of where the Variable Limiter Control is set, you may defeat the Limiter circuit at any time by pulling out on the Limiter knob itself. (It doubles as an on/off switch for the Limiter.) To defeat the Limiter, simply pull "out" on the knob of this control until you hear and feel a "click." To re-engage the Limiter, push the control back in to its original position, and the Limiter circuit will reactivate at the threshold setting you chose originally. This may be useful in determining just how much limiting is occurring in an "A/B" type of test. You can also hear in an instant if your limiter is set to where it is actually stopping the power amp from clipping, because if you suddenly hear distortion that wasn't there when the limiter was engaged, that's exactly what's occurring. (This is especially key to remember when using your 2x10C with an extension cabinet at high volumes.)

LIMITER ACTIVE LED

When the threshold (starting point) of the Limiter circuit is reached, the Limiter Active LED will light, indicating that the Limiter Circuit is active and helping to protect your power amplifier from clipping. The Limiter LED will not illuminate when: a) the Limiter has been defeated by pulling out on the Limiter control; b) when playing at levels not high enough to engage the circuit.

NOTE: If you have defeated the Limiter and you hear a loud, sharp distortion present in your sound − and the Preamp Clip LED is not lighting up − re-engage the Limiter by pushing the Limiter control back in. If the distortion goes away, you were probably clipping the power amp, which is not a good thing. Remember, the Limiter circuit is there to protect your amplifier from such a state of opera- tion.

8 • WORKINGMAN’S 2X10C

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Workingman’s 2X10C Introduction Workingmans 2X10C Front Panel Features SpecificationsCabinet Construction and Features Workingmans 2X10C Getting StartedBalanced D.I. XLR Output Tuner OUTInput Jacks PASSIVE/ACTIVE Input JackAural Enhancer Gain ControlPreamp Clip LED Using the 5-BAND Graphic EQ Section Bass Control Workingmans 2X10C 5-BAND Graphic EQ SectionOverview Midrange ControlsEffects Blend Control Variable Limiter Control with defeat optionDefeating the Limiter Circuit Limiter Active LEDMaster Volume Control Speakers ON/OFF SwitchHeadphones Jack stereo only Power ON/OFF SwitchEffects Receive Effects Loop for outboard effects devicesEffects Send Combo Cabinet JACK/PLUG Assembly HOW Impedance Affects Power RatingsWorkingmans 2X10C Power Amplifier Minimum Impedance Ratings Extension Speaker Output SectionWorkingmans 2X10C Power Delivery Capabilities Power Ratings Your rigSpeaker Fuse Internal Speaker Mode SwitchExtension Speaker Output Jacks Workingmans 2X10C Suggested Settings Tweeter Mode SwitchLine Fuse A/C or Mains Fuse Cord ReceptacleWORKINGMAN’S 2X10C WORKINGMAN’S 2X10C Limited Warranty

2X10C specifications

The SWR Sound 2X10C is a powerful and versatile bass cabinet designed for both studio sessions and live performances. With its compact size and lightweight design, it is an ideal choice for musicians seeking portability without sacrificing sound quality. The cabinet features two 10-inch custom-designed speakers, specifically engineered to deliver a balanced tonal range and impressive low-end response.

One of the standout features of the 2X10C is its high power handling capability, allowing it to handle up to 400 watts RMS. This ensures that even when pushed to its limits, the cabinet maintains clarity and punch, crucial for any live show or recording environment. The cabinet is also equipped with a high-efficiency horn tweeter, which enhances the higher frequencies and provides a sparkling top-end that complements the rich tones produced by the 10-inch woofers.

The cabinet utilizes SWR's proprietary technologies to enhance performance. The "Bass Reflex" design features strategically positioned ports that help to eliminate unwanted air turbulence while maximizing low-frequency response. This design not only promotes deeper bass tones but also allows the cabinet to remain lightweight, making it easier for musicians to transport.

Another key characteristic of the SWR 2X10C is its rugged construction. Built from durable materials, the cabinet is designed to withstand the rigors of both touring and frequent use. Reinforced corners and a heavy-duty grille protect the speakers from potential damage, ensuring the longevity of the cabinet.

For connectivity, the 2X10C comes with dual 1/4-inch input jacks, enabling easy integration with various amplifiers and allowing for daisy-chaining additional cabinets if more sound output is required. The cabinet is compact enough to fit into most environments, making it a versatile option for a range of musical genres.

In summary, the SWR Sound 2X10C combines advanced features, innovative technology, and robust build quality, making it an exceptional choice for bass players looking for a reliable cabinet that delivers impressive sound across various settings. Whether in a rehearsal space, a studio, or on stage, the 2X10C stands out as a top-tier option that meets the demands of modern musicians.
Top Page Image Contents